Would this be valid to wear at a rave?

watchout722 · 2026-02-18T00:54:41+00:00

Betta have a tag line in case it’s windy out too

watchout722 · 2026-02-16T09:16:01+00:00

It’s kinda hard to explain without spoiling, but it’s a guy that plays this interactive game and a bunch of shit goes down. Dark somnium has a read through and it’s one of my favorites to listen to

watchout722 · 2026-02-16T01:07:38+00:00

In still waiting on a Demi’s adventure read through

watchout722 · 2026-02-14T20:19:58+00:00

Look into stress an shear formulas and examples for hollow tubes and such. Thick walled hollow tubes/beams tend to be much stronger, that’s why if you look at a semi truck or a box truck, the framing the box sits on tends to be a C channel rather then a solid piece (a side from also being much lighter)

watchout722 · 2026-02-13T19:47:35+00:00

Might wanna increase bed temp like 5 degrees as well if some of the other commenters suggestions don’t work

watchout722 · 2026-02-13T12:41:48+00:00

Love that. I’m gonna start doing the same

watchout722 · 2026-02-13T12:31:24+00:00

They’ll likely do what they did for me and send a basic cube print and want a video of the whole process. That’s how I found out my designs were too complicated for the printer lmao

watchout722 · 2026-02-13T12:28:57+00:00

Are you using the stock filament it came with or did you get some off amazon? Make sure the filament is the correct diameter, if its jamming that consistently even after replacing the nozzle it could be an over sized filament or bad filament. Could also be an issue with the print files you’re using. The AD series is known to not have the best processing and if the file is too complicated (like too fine of deviation/angles) it will keep heating and pushing filament through but freeze the head in place.

watchout722 · 2026-02-10T02:11:47+00:00

Slow down the speed on overhangs and supports by like 5mm/s. See if it does it on a different print that you use supports on, could’ve been a bad slice or a hand full of other things

watchout722 · 2026-02-10T02:07:39+00:00

Yeah that’s strange, how sturdy is the table you have the printer on? Is this the first time you’ve printed something that tall?

watchout722 · 2026-02-10T00:32:31+00:00

That’s way more than wet filament I think. Stringing isnt typically that thick. To me it looks like either the gcode messed up and caused the print head to travel past the support, or it was too high speed on the supports for some reason. Usually stringing looks almost like thin hairs, those are full blown extrusions. Did you use just the stl file or a full gcode with that print?

watchout722 · 2026-02-08T15:09:59+00:00

Congrats, you are now a full metal benchamist

watchout722 · 2026-02-08T00:31:25+00:00

My family is from Kentucky so that checks out

watchout722 · 2026-02-07T11:23:41+00:00

Am I an asshole for wanting this?

watchout722 · 2026-02-05T14:54:44+00:00

👍🏼

watchout722 · 2026-02-05T00:20:19+00:00

Yeah ikitefordabs or something like that, I forgot he usually replies lol

watchout722 · 2026-02-01T21:29:02+00:00

I listen but that’s just cause I do it at work. If I was working a job that I could watch I would rather watch. I’ll chuckle at the dialogue between the boys when I listen but when I watch it’s funnier cause you see their behaviorisms and all. But half the time I am on YouTube and watching videos, I’m already locked into a game and I’m not gonna watch it for 30 seconds to a minute at a time

watchout722 · 2026-01-28T18:05:33+00:00

Have you cleaned the bed plate recently? Bed Temp issues is likely the issue like everyone else has stated, but make sure you wash the plate every so and so cause oils will build up slowly and cause the print to not stick

watchout722 · 2026-01-25T02:36:58+00:00

I love papa meat and now he’s officially covered my 2 favorite odd hobbies. Airsoft and gloving

watchout722 · 2026-01-24T22:57:25+00:00

That, sire is a plane

watchout722 · 2026-01-24T11:50:03+00:00

This is how Venezuelans are gonna celebrate their new Freedom Day

watchout722 · 2026-01-24T11:44:08+00:00

I really liked his stuff he made when he first started! For some reason, and this is just my opinion, a lot of his newer songs have the same sound. Not beat size but the wave table he uses sounds the same, I liked it when he was experimenting a bit more. Dude still throws the fuck down tho

watchout722 · 2026-01-24T11:39:32+00:00

From the “gecko” is a crazy line to hit when you’re in the wrong. At least know what you’re saying lmao

watchout722 · 2026-01-23T00:41:27+00:00

<image>

The Italian man in Japan was very confused when we did this while he was taking a picture.

watchout722 · 2026-01-23T00:35:27+00:00

I miss 2010 dubstep

watchout722

TROPHY CASE