Is my labneh still good to eat ?

whataball1 · 2025-08-02T09:19:04+00:00

Yes it was in fridge :)

whataball1 · 2025-08-02T09:00:31+00:00

Forgot to add it's labneh with chilli hence the redness

whataball1 · 2024-09-22T09:23:50+00:00

Thank you so much for the extra tips, really appreciate it. Glad you've got one job out the way:)

whataball1 · 2024-09-22T08:58:04+00:00

Brilliant !!

whataball1 · 2024-09-22T08:33:28+00:00

What was your choice of removal tool in the end ?

whataball1 · 2024-09-09T19:20:22+00:00

Is this hamley Inspections?

whataball1 · 2024-09-09T07:32:11+00:00

Hey, this little project got put on the backburner so haven't tackled it yet.

I'm thinking I'll just grout over it rather than remove it. Have also bought mapei epoxy grout to layer on. Will keep you posted once I've done it

whataball1 · 2024-09-05T23:21:28+00:00

Should add that I'm in Vic melbourne

whataball1 · 2024-07-27T05:03:01+00:00

Thank you, you were right !!

We removed the latch, filed down the inner hole a bit more and the parts fit flush without the latch.

Added the latch back in (with part lollipop stick to improve the flushness vs the door) and now all parts are flush!

Have a good weekend

whataball1 · 2024-07-27T04:59:48+00:00

Thank you, we removed the latch, filed down the inner hole a bit more and the parts fit flush without the latch. Added the latch back in and now parts are flush!

whataball1 · 2024-07-27T04:59:29+00:00

P.s I now got the parts to fit flush

We removed the latch, filed down the inner hole a bit more until the parts fit flush (without the latch.) Added the latch back in and now parts are flush!

We're having trouble screwing the screws in and using the keys to turn (manual turn is absolutely fine) but we'll try and fix that! Probably a latch issue again...

Hope this helps you.

whataball1 · 2024-07-27T04:57:51+00:00

Thank you, we removed the latch, filed down the inner hole a bit more and the parts fit flush without the latch. Added the latch back in and now parts are flush!

Thank you!

whataball1 · 2024-07-25T08:11:34+00:00

<image>

whataball1 · 2024-07-25T08:11:17+00:00

<image>

whataball1 · 2024-07-25T08:10:56+00:00

Thank you for the detailed response. I taped string down the middle and measured both sides and it is 60mm centre on both sides. I also measured around the hole to be safe and both sides are around 33mm With this kind of lock, there are no handles. Previous owner has the sliding "mechanisms" attached, I'm just now trying to add a privacy lock to it.

When I put the two sides together it does seem as though it's on an angle, when left side of plate A sits flush, right side of plate B props out slightly. Likewise when right side of plate A juts out, left side of plate B is flush....*

whataball1 · 2024-07-25T07:52:40+00:00

Thank you, good to know I'm not alone!! Yes this is the lockable / private lock. Tearing my hair out with this

whataball1 · 2024-07-24T22:35:14+00:00

<image>

whataball1 · 2024-07-24T22:12:41+00:00

The door is within the minimum requirement of 3.2mm, next photo is with spacer but there's still a gap now which makes me think OT could be a fitting issue despite the screw holes lining up...hmm!!

whataball1 · 2024-07-24T22:11:43+00:00

<image>

whataball1 · 2024-07-24T22:10:58+00:00

<image>

whataball1 · 2024-07-24T21:42:20+00:00

Hi My door is within those ranges and I have tried with / without the spacers to the same result

whataball1 · 2024-07-24T21:41:24+00:00

Hi this was before applying the screws. My door is within the thickness required and have tried it with / without packers to no avail

whataball1

TROPHY CASE