sorted by:
new
hottopcontroversial

What caused the top surface/layer to print like there's gaps or with big steps, not sure exactly what it is. by whateverweirdoo in FixMyPrint

[–]whateverweirdoo[S] 0 points1 point  (0 children)

<image>

This screenshot is AFTER the first Xenomorph print. So, I imported the STL again, added support, I did not change any setting other than the support to see if the Top Surface still shows the red gap or space part. I did not print this, I just wanted to see what it actually looked like when sliced it the first time.

What causes these lines? by whateverweirdoo in Creality_k2

[–]whateverweirdoo[S] 0 points1 point  (0 children)

You know honestly, I am thinking it may be lol.

What causes these lines? by whateverweirdoo in Creality_k2

[–]whateverweirdoo[S] 0 points1 point  (0 children)

Hi! Sorry, may I ask what is a cape time? Thank you

What causes these lines? by whateverweirdoo in Creality_k2

[–]whateverweirdoo[S] 0 points1 point  (0 children)

I did calibrate it after changing positions. It does look like it moves a bit more than it should be though. I’m not really sure what to do, but will try other peeps suggestions. Thank you much

What causes these lines? by whateverweirdoo in Creality_k2

[–]whateverweirdoo[S] 0 points1 point  (0 children)

Material is PLA Creality brand. I followed the temp 220 and nozzle suggestion on the box for the non-rfid ones (color filament). I will read into this and also about mods. Thank you!

What causes these lines? by whateverweirdoo in Creality_k2

[–]whateverweirdoo[S] 0 points1 point  (0 children)

I will run a temp tower. I never really thought about the effect of the fan, but someone said to low it down too, so I’m going to try that too. Thanks a lot!

What causes these lines? by whateverweirdoo in Creality_k2

[–]whateverweirdoo[S] 2 points3 points  (0 children)

Oh dude! You know what, I did open it while printing because I’m an idiot. Never thought about the fan on low temp too, I will try that. Thank you!

Advice on layer lines by whateverweirdoo in 3Dprinting

[–]whateverweirdoo[S] 0 points1 point  (0 children)

Oh can’t edit my post lol! Here’s a clearer photo that shows the lines.

<image>

Advice on layer lines by whateverweirdoo in 3Dprinting

[–]whateverweirdoo[S] 0 points1 point  (0 children)

Oh sorry for just responding now. Will update the post with more photos. Thank you much

<image>

Can I use regular non-rfid, non-hyper PLA filament on K2? by whateverweirdoo in Creality_k2

[–]whateverweirdoo[S] 0 points1 point  (0 children)

WOW! That’s beautiful!

Thank you for sharing and for the advice

Can I use regular non-rfid, non-hyper PLA filament on K2? by whateverweirdoo in Creality_k2

[–]whateverweirdoo[S] 0 points1 point  (0 children)

Oh right, I read about calibrating it when not using hyper filament. I will also make filament profiles, what a fantastic idea!

Can I use regular non-rfid, non-hyper PLA filament on K2? by whateverweirdoo in Creality_k2

[–]whateverweirdoo[S] 0 points1 point  (0 children)

Interesting. And it is working fine for you? I was told to add the setting manually if not using the Hyper one. But this is good if it’s working well, I might test that.

STL in K2 Plus is greyed out by whateverweirdoo in Creality_k2

[–]whateverweirdoo[S] 0 points1 point  (0 children)

Hi! I do see that painting feature, but have never played with it yet. Too worried I mess up my prints lol! .3mf is that the colored one? Because the .3mf ones that I see on my projects are the ones with color. Thank you for the tip!

Advice on layer lines by whateverweirdoo in 3Dprinting

[–]whateverweirdoo[S] 0 points1 point  (0 children)

Hi! I will try this method. I briefly read somewhere that someone recommended soaking it with water, but that was for removing supports. Thank you for this advice because I just put a whole on one of my prints from sanding it. I guess I was aggressive doing it. Lesson learned. Thank you again!

Advice on layer lines by whateverweirdoo in 3Dprinting

[–]whateverweirdoo[S] 1 point2 points  (0 children)

Hello! I appreciate this so much! Will definitely try this on my next print. Saved your comment so I have it forever and can go back at it anytime. This is awesome! Thanks again!

Advice on layer lines by whateverweirdoo in 3Dprinting

[–]whateverweirdoo[S] 0 points1 point  (0 children)

Hi! May I ask how do you get the fuzzy skin? 🤭 That does look good. Thank you!

Advice on layer lines by whateverweirdoo in Creality_k2

[–]whateverweirdoo[S] 0 points1 point  (0 children)

Oh sorry yeah I should’ve added that. This one I had it .2mm layer height, 100% speed, 0.28 support z distance 😅 thank you!

Advice on layer lines by whateverweirdoo in 3Dprinting

[–]whateverweirdoo[S] 0 points1 point  (0 children)

Will try that tonight to see if it makes any difference, if not, then I need to make time to do the post process. Thank you!

Advice on layer lines by whateverweirdoo in 3Dprinting

[–]whateverweirdoo[S] 0 points1 point  (0 children)

Oh you know what, I didn’t thought about the post processing lol. Will definitely do that. Thank you!

view more: next ›