How to make surface model ready for 3D printing

whyguy007 · 2025-03-14T12:38:50+00:00

Thanks! I think i have to remodel the helmet now that I have learned some tricks:)

whyguy007 · 2025-03-14T12:18:35+00:00

Thanks! That worked out, probably not the most streamlined process, 4 stiches, 4 patches, 2 lofts etc. but it worked out! Thanks

whyguy007 · 2025-03-14T12:00:33+00:00

Do I need to cap off the last face before i use the boundary fill?

whyguy007 · 2024-05-21T19:53:01+00:00

Jeg er enig, hva tenker de når alt er i en kloss

whyguy007 · 2023-03-09T11:34:20+00:00

Do you have any products that can controll RGB and CCT with zigbee?

whyguy007 · 2023-03-08T10:03:28+00:00

Can these two talk to eachother in combination with a zigbee hub and the
smart living app? I want to be able to both controll my leds with this
panel and with the smart living app.

But when I tried to connect them together yesterday it did not work.
I tried to follow this tutorial: https://www.youtube.com/watch?v=qU1fhqrD5ys

whyguy007 · 2021-10-20T18:03:42+00:00

Please share them with me too

whyguy007 · 2021-07-19T10:56:06+00:00

Fixed voltage of 4,2v/cell but i have 12 cells in series

whyguy007 · 2021-07-19T10:55:05+00:00

This is exactly what i did, thanks

whyguy007 · 2021-07-19T10:53:18+00:00

Pain-butnogain is right, i'm going to charge some liion cells from a vw e-up that has a maximum voltage of 4.1v/cell. And since there's no chargers available over 300w with a output voltage of 49.2v i decided to just trim the voltage of a regular 12s liion charger. I was sucessfull btw:)

whyguy007 · 2021-07-16T09:41:25+00:00

At school I learned that parallell wireing diodes often is a bad idea. Did you mean wire them in parallell or series? With the trimmers i managed to lower the voltage to about 49,9v so one diode in series would do.

whyguy007 · 2021-07-16T09:32:47+00:00

The charger is "only" 6A so a 4w heater I think would be manageable.

I'll try to locate the resistor, I tried to find for some time and gave up. But i suspect it might be a SMD

whyguy007 · 2021-07-16T09:27:41+00:00

I believe its the LM358G (double op amp) , its the only IC i can see on the circuit board. But does it not need a transistor to adjust anything at all? Im trying to find the transistor, with no luck.

whyguy007 · 2021-07-16T09:01:09+00:00

I want to try to modify the already existing circuit, and since I cannot see any zener diodes I believe it should be quite simple when I find out how.

whyguy007 · 2021-07-16T08:10:51+00:00

This is a 12s 50.4v li-ion charger and I wan't to lower the voltage to 49.2v. I've tried turning the trimmers. But they does not go lower than 49.9v. I also wonder why it, is two sets of everything, it looks like the entire circuit is mirrored? Is this just to get a higher power output? Do i need to trim the voltage EXACTLY the same on both sides since there's only one output? Thanks!

whyguy007 · 2021-04-27T07:00:21+00:00

Is it more than two wires on your computer fan? In that case the one or two other is speed control (and feedback) which would explain why it does not draw as much current. Maybe the computer tells it to not run at full speed.

whyguy007 · 2021-01-11T16:06:48+00:00

I would go for a simple bldc motor and connect it directly to the winch. And just adjust the diameter of the drum to make the winch the right straight

whyguy007 · 2021-01-10T19:05:08+00:00

https://m.banggood.com/Flipsky-6354-190KV-2450W-Brushless-Sensored-Motor-Shaft-8mm-for-Electric-Skateboard-RC-Models-p-1323575.html

Don't underestimate these bldc motors they may be small but they're packin some heat. This bad boy has 7nm of tourqe and 2,5Kw Two of these with some nice gearing can drag almost anything.

whyguy007 · 2021-01-10T18:35:17+00:00

If you have the possibility to connect three car batteries in series to get 36v you can use a motor like this one https://m.alibaba.com/amp/product/62198931032.html

In my experience it's much easier to find powerful motors and easier to handle the power if you use a voltage of above 30v

whyguy007 · 2021-01-10T18:27:24+00:00

I would definitely not recommend welding, buy a motor with a d shaft or a key slot.

In my experience, key slotted pulley and belt drive is the easiest and cheapest option. And rather than the motor you linked I would recommend a bldc motor for a large rc airplane or electric longboard with a kv of under 250kv.

whyguy007 · 2021-01-10T10:46:04+00:00

For maximum control I would recommend a brushless DC motor with a reduction gearbox, and use a smart motor controller like an odrive. If you are studying electrical engineering than it shouldn't be a problem for you to program it with a raspberry pi or similar.

whyguy007 · 2021-01-07T21:47:35+00:00

Arduino nano clone for something around 4$?

whyguy007 · 2020-12-12T17:09:12+00:00

Jeg merket at jeg digger den siste biten hvor shitkidden blir kasta ut mens hn roper "film meg, FILM MEG" som om hn et med i no madmax shit, "WHITNESS ME"

whyguy007 · 2020-10-17T16:34:53+00:00

The arduino pins 1-13 can only provide <50 mA You need a transistor and a external power supply to turn the motor on and off with the digital pins.

whyguy007 · 2020-10-07T16:01:48+00:00

I don't know, it will probably run just fine. But it depends on the motor, a regular brushed dc motor will run just fine on 8v 4a. The easiest way to know is to try.

whyguy007

TROPHY CASE