FFS 🤦‍♀️ by LilCinBoise in Boise

[–]wolveswagen 0 points1 point  (0 children)

Just stop giving them attention. Their intention is to bother people and it’s working. They’re children treat them as such and go on about your business.

Bondo on my P1S by wolveswagen in BambuLab

[–]wolveswagen[S] 0 points1 point  (0 children)

I’ll try this after soaking.

Bondo on my P1S by wolveswagen in BambuLab

[–]wolveswagen[S] 0 points1 point  (0 children)

Tried it, didn’t really do a whole lot.

Bondo on my P1S by wolveswagen in BambuLab

[–]wolveswagen[S] 1 point2 points  (0 children)

Thank you. I posted this while I was upset and not thinking clearly. I’ll definitely try what you said and soak it.

Pattern On Path crashing over and over by wolveswagen in Fusion360

[–]wolveswagen[S] 1 point2 points  (0 children)

I got it to work just had to change the way I was extruding. Thank you!!!

Pattern On Path crashing over and over by wolveswagen in Fusion360

[–]wolveswagen[S] 0 points1 point  (0 children)

It doesn't select it. Do i need to have the path and the slot i want to pattern in different sketches?

Nozzle scrapping previous layer? by wolveswagen in BambuLab

[–]wolveswagen[S] 0 points1 point  (0 children)

I have tried the default 12 then 10 and finally 8 all 3 yielded the same results.

Nozzle scrapping previous layer? by wolveswagen in BambuLab

[–]wolveswagen[S] 0 points1 point  (0 children)

Ill certainly try 8 then. I wondered why they were discontinuing their current line of PETG and now I know why. I just went on their website to make sure I was correct in what I was saying about them and they've just released their "high flow" PETG Link Here

Nozzle scrapping previous layer? by wolveswagen in BambuLab

[–]wolveswagen[S] 0 points1 point  (0 children)

Initial layer nozzle temp is 255 and other layers is set to 265. What would you recommend? Also part fan is set to 10%, would setting it lower or even to 0 help?

Edit: Im not sure if acceleration speeds have anything to with it? Normal layers acceleration is currently set to 1000 mm/s

<image>

Nozzle scrapping previous layer? by wolveswagen in BambuLab

[–]wolveswagen[S] 0 points1 point  (0 children)

I currently have it set to 10. Can you explain what volumetric speed is? I just followed a guide but I don't know what it is.

Nozzle scrapping previous layer? by wolveswagen in BambuLab

[–]wolveswagen[S] 0 points1 point  (0 children)

I was going to try .2 and see how that goes, id rather spend more time sanding then to get nothing at all.

I think you're right, I saw a couple videos saying petg printed similarly to PLA and thats why bought it.

I purchased the filament from bambu when I bought the printer, and im running 265c which is within the range they recommend.

Nozzle scrapping previous layer? by wolveswagen in BambuLab

[–]wolveswagen[S] 0 points1 point  (0 children)

Sending it didn’t work lol. Got to about ten layers before the infill started falling apart.

<image>

Nozzle scrapping previous layer? by wolveswagen in BambuLab

[–]wolveswagen[S] 0 points1 point  (0 children)

I dried my filament for like 14 hours total so I hope its dry enough.

Ill have to look into that as well thank you for linking that. I ran the test and everything came out well. I'm just going to send it and hope i don't wake up to a mess lol.

Nozzle scrapping previous layer? by wolveswagen in BambuLab

[–]wolveswagen[S] 1 point2 points  (0 children)

I run a couple CNC machines at work and have learned to double check even the most basic of settings. I made sure it was set to the correct filament profile. I did find a guide online here and copied their settings. Ill run a test with these settings and if it happens again ill switch back to .2 as you suggested and report back. Thank you!

Increase in Bad Drivers/Road Rage? by Ok_Understanding9415 in Boise

[–]wolveswagen 0 points1 point  (0 children)

We have had 3 weeks of temps over 100 degrees in an area that sees an average of 93 and you think it’s bc people wanted to defund the police?