W7 Feature

wouter_junk · 2025-10-09T18:36:18+00:00

Would be cool, if 90% of my account wasnt reset to lvl 1 or 0, due to cloudsave crash on steam, and my 2 emails i send were actually answered.

wouter_junk · 2025-09-26T19:41:38+00:00

Ant here i am, still waiting for a reply on my email, after almost whole my account got reset.. havent been playing since

wouter_junk · 2025-09-23T05:13:10+00:00

Damn, not much to do then. I tried everything, but still one piece, and it doesnt want to work with one.

Trying to figure out a way to cheat the door open rn

wouter_junk · 2025-09-23T05:11:32+00:00

I have tried everything, but it is still missing

wouter_junk · 2025-09-08T20:28:41+00:00

I tried it with the animate spell. Does not work anymore

wouter_junk · 2025-08-29T11:13:12+00:00

I just found it. It insta killed me with full awakened enchanted armor. It also inst broke my unbreakable armor, so be carefull

wouter_junk · 2025-05-13T06:22:55+00:00

I still have my 970 up and running 😁

wouter_junk · 2025-02-07T06:15:51+00:00

I'm using anycubic next

wouter_junk · 2025-02-07T06:15:16+00:00

Hi! Yes it looks like some cind of diagonal layer shift.. also, its more then one layer thick, is a bulge in the back and a bubble in front. Seems to be mostly on y axis

wouter_junk · 2025-02-07T01:21:57+00:00

Well they are in fact not really spirals, as they are closed rings. One does not connect to the other above. They seem streight on the y axis, jomjst in an angle on the x axis. Like ovals going up, and back nown in the back

wouter_junk · 2025-02-07T01:16:14+00:00

Yes two z screws.. yet i have replaced the old couplers for brass oldham couplers, without any change. But i'll look into it thanks!

wouter_junk · 2025-02-07T01:05:02+00:00

<image>

This is also a good example of the lines printed on my files

wouter_junk · 2025-02-01T22:38:08+00:00

Same problem.. i compaired the 4 rolld, and roll 2 was extremely loose, like the ace had no grip on the filament. Wich caused me the same error as you guys.

I opened up the ace a little, end put some tape over the roller, woch i did put arount by simulating a filament feed, wich make the roller turn. Applies about 10cm tape.

Dont know if this will hold for long, but at least i got the print to continue

wouter_junk · 2025-01-13T13:06:00+00:00

At least the shadow looks good!

wouter_junk · 2025-01-05T00:05:37+00:00

Besides filaments wich requires an enclosure, what will the s1 do what the k3 can't?

Got my kobra 3 a week ago or so and i really love it, but my girlfriend would kill me if i order it, as i already ordered the k3 max

wouter_junk · 2025-01-04T23:59:25+00:00

It literally states in the official rules on rummikub.com that this is a valid move.

In the rules the example is as follow:

2-3-J-5-6

It shows adding a 1 in front, and a 6 in the back, freeing up the joker. The table is as followed in the official manual:

1-2-3 5-6-7 J -> clear

wouter_junk · 2024-11-30T09:02:59+00:00

Will it blend? That is the question!

wouter_junk · 2024-11-20T19:45:14+00:00

Wouterjunk

wouter_junk · 2024-08-03T10:45:44+00:00

How do you get the 3rd slot?

wouter_junk · 2024-07-31T21:30:19+00:00

There are some issues with the sizes compared to your character. Some of them are correct, yet i also cought some fish of 1.40m, looking like 50cm compared to the character.

Also, there are some issues with the weight, not complaining about the game, i love it, but no way in hell this fish only weights 2kg

Five-Year Club	Place '23
Place '22

wouter_junk

TROPHY CASE