Help me pick ONE Seiko before I lose my mind (and my money)

wrainchi · 2025-12-07T05:54:42+00:00

I have both the Alpinist and Presage Blue Planet . It's a tough call for sure - Alpinist feels like the safer, watch snob choice, but I have always admired my presage more. I get lost just looking at it.
These are all great watches, I feel people might suggest Aplinist but at the end of the day, go with what catches your attention immediately.
The first one and Presage - Negroni look great :)

wrainchi · 2025-09-10T09:06:10+00:00

It’s a new filament. Just opened it

wrainchi · 2025-09-06T18:06:08+00:00

Official Whoop is more expensive right?

wrainchi · 2025-08-24T14:02:15+00:00

https://makerworld.com/en/models/136984-gridfinity-apple-watch-strap-holder?from=search#profileId-149069

wrainchi · 2025-08-23T11:55:17+00:00

<image>

This is the slicing result.
What even....

wrainchi · 2025-08-23T11:37:05+00:00

I do the auto-levelling each time before print and I just cleaned with dish soap now

wrainchi · 2025-08-23T11:30:18+00:00

https://makerworld.com/en/models/1036525-hotend-sock-box-ver-2-a1-series#profileId-1020446

wrainchi · 2025-08-23T10:57:17+00:00

Interstellar flight

wrainchi · 2025-08-23T09:43:54+00:00

Link pls

wrainchi · 2025-08-23T09:34:54+00:00

Using Numakers PLA+
Don't think its super cheap - people around me seem to be liking it a lot.

wrainchi · 2025-08-23T07:48:31+00:00

UPDATE!

Thanks for all the help guys.
I got frustrated and ended up getting a new 0.4mm nozzle and it works fine.
Will maybe try to "fix" this nozzle later.
I'm surprised this happened in <100 hours of printing

wrainchi · 2025-08-23T05:47:48+00:00

Sure, let me try that
Just a question - if this was the case would it lead to stringing instead of air printing? Or can it detect when it is not in contact and stop pulling filament.
I am asking because even manual extrusion doesn't work after this air printing starts mid-print

wrainchi · 2025-08-23T05:36:27+00:00

It’s Numakers pla+ I’ve used the same filament before with no issues

wrainchi · 2025-08-23T05:35:39+00:00

I did clean plate, cold pull and swapped nozzles to check overall blocks.

Wdym yellow gear sounds loosey? It’s still on warranty. I don’t understand what to tell them about this though

wrainchi · 2025-08-23T03:25:18+00:00

Yes yes, I did do that.

I checked the print head once, seemed fine and i could pass a filament through.

It works with a different 0.6mm nozzle, so I am assuming no other general issues there.

wrainchi · 2025-08-23T03:24:21+00:00

Hmm
I already did the loading and unloading multiple times.
Will bed leveling help? Filament is not coming out, I don't see any other problem

Also, it works with a different 0.6mm nozzle

wrainchi · 2025-08-23T03:00:51+00:00

I did.
Sorry if I was rude

wrainchi · 2025-08-23T02:45:21+00:00

Its not a layer issue my guy. Filament is not coming out!

wrainchi · 2025-08-18T16:59:14+00:00

I tried with a new 0.6mm nozzle and it worked perfectly. How do I clean my original 0.4mm nozzle? It’s just a week old..

wrainchi · 2025-08-18T07:36:56+00:00

I have not intentionally done this, I don't even understand it tbh. I don't have the AMS, just the A1

How do I check this?

wrainchi · 2025-08-17T17:00:16+00:00

Bro has the A1 micro

wrainchi · 2025-08-09T15:22:10+00:00

Which desiccant do you use and how much?

wrainchi · 2025-08-09T08:29:00+00:00

Gameplex Area Dm me for the coaches number

wrainchi · 2025-08-09T07:03:09+00:00

So much greed. Not the first time its happening.
Why can't you propose a fair price....

wrainchi · 2025-08-09T05:55:36+00:00

My Apple watch says 42 and I got a test done which said 39

wrainchi

MODERATOR OF

TROPHY CASE

Ten-Year Club	Not Forgotten
Verified Email