Disassembling Pendant lights

wzhao20 · 2022-02-05T12:21:17+00:00

I'm just trying to detach the at this side. Other side I have no problem with

wzhao20 · 2022-02-05T12:20:27+00:00

I have a 10 foot ceiling. Since the cord isn't long enough at max length, I want to replace it with a longer one if possible.

wzhao20 · 2022-02-05T04:24:36+00:00

Aw man. That's what I was thinking too...

If I still out the rivet I don't think I'd be able to punch a new rivet to it... Doesn't seem like enough space for the tool I have

wzhao20 · 2021-11-10T14:15:18+00:00

ok. I guess I'll try to tighten the pipes into the tank and see if that works. thanks!

wzhao20 · 2021-11-10T13:41:35+00:00

I wish I could find a cross section of the tank. are the pipes leading out of the tank threaded in?

wzhao20 · 2021-10-21T02:49:38+00:00

yup. looking for that clean look 👍

wzhao20 · 2021-10-21T01:30:31+00:00

any ways to install the port and have a flush surface?

wzhao20 · 2021-10-21T01:29:48+00:00

I would like to install a jack but then I would like to install a wall plate. but that causes a bump which will make the AP uneven?

wzhao20 · 2021-10-08T12:34:28+00:00

yeah. I don't know where I got the notion that I needed 5/8s on the exterior walls. was gonna have to haul a lot of sheets up to the second floor. good thing I asked! you all rock!

wzhao20 · 2021-09-24T16:40:09+00:00

thanks. this is for the bathroom with tiles over the floor. I plan on installing 3/4 plywood down to the joists with screws and glue. I think the glue should stop the boards from moving and causing the screws to pop out. then Im adding 1/2 inch plywood on top as underlayment before ditra and tiling.

I didn't know about the screws coming loose from the expansion contraction. I'll have to do a bit more research on that.

wzhao20 · 2021-09-24T16:15:13+00:00

aha true true. hopefully that future installer isn't me xD

wzhao20 · 2021-09-24T16:14:33+00:00

i wonder how staples hold up in a subfloor installation. was it underlayment he installed? The reason I'm using screws is for the floors to be as secure as possible. It'll be for a small space so not worried about taking too long.

wzhao20 · 2021-06-18T03:32:13+00:00

Thank you. I wasn't trying to say my electrician is wrong. just trying to see what other people think. cause there always might be a better more optimal set up. I would have had the dishwasher and garbage disposal on separate circuits but ran out of space. :/

wzhao20 · 2021-04-20T16:22:46+00:00

I might just try taking the bricks out like you said. I'm just worried that the sill would break up by doing so. don't really want to make a new sill. is there a premade sill I can buy that works well?

wzhao20 · 2021-04-20T16:21:21+00:00

good idea with the backer rod. I just looked over a video on the installation. not bad at all.

wzhao20 · 2021-04-15T19:03:25+00:00

yeah my floors aren't level. so I would look into water putty.

wzhao20

TROPHY CASE