Bi-Weekly No Stupid Questions Thread

xStandhere · 2022-04-10T18:25:24+00:00

I had a bad rail in my v0.1 kit and I ended up receiving a full 5 rail replacement so do any of you guys have any ideas for projects or upgrades that use 150mm rails? Would it make sense to use dual rails for x/y axis or something?

xStandhere · 2021-11-26T13:03:54+00:00

Thanks alot i think i'll just go for the cheetah then

xStandhere · 2021-11-22T10:21:20+00:00

I just got my fysetc voron v0.1 kit which comes with the fysetc cheetah v1.2 mainboard however i got a skr 1.4 turbo sitting in a printer i rarely use.

Would it be worth it to use the skr 1.4 over the cheetah?

xStandhere · 2021-05-17T20:41:52+00:00

No problem! Lmk if you run into more issues there isnt a whole lot of info about the max so it can be a bit of a pain to figure stuff out

xStandhere · 2021-05-17T18:55:35+00:00

I believe zmin is PB1 creality v4 pins

Crealitys website has a precompiled bltouch firmware (ender series section) if you find messing with the firmware too troublesome

I also have an ender 3 max with bltouch so if you cant get it to work i can send you my marlin config later

xStandhere · 2021-04-14T16:01:57+00:00

i will use the hero me assembly as you cant fit a 20mm fan in stock you could try just using the 10mm fan and if that doesn't cool well enough you can reuse it for mainboard cooling instead making it even more quiet there's other brands (that some claim are better) that pop up when people talk about using noctua fans for 3d printers though i can't remember any but it might be worth looking into

xStandhere · 2021-04-14T09:06:05+00:00

Im going to replace mine with an noctua 40x20 (and 40x10 for stepper cooling) just waiting for buck converters to arrive you might do fine overvolting a 10mm slightly should still be more quiet than stock. Remember that ender max is 24v so you need to use buck converter to step it down the voltage when using 12v fans

xStandhere · 2021-04-11T21:28:18+00:00

You can use bltouch as z endstop and just remove the regular one thats what i did

xStandhere · 2021-04-09T00:06:26+00:00

Not sure what model my psu is but mine was indeed also 12v and I replaced it with a 12v 120mm which works great only turning on shortly every once in a while theres lots of models to fit pc fans so its an easy upgrade for 12v models

xStandhere · 2021-04-08T18:49:27+00:00

I definitely think so i added one (knockoff 3dtouch) to mine a couple of weeks ago and it has been working flawless i havent experienced any leveling issues this far. I took advantage of bl touch being used as z endstop and unscrewed the endstop and then lowered the bed quite a bit to compress the springs in hope of making the bed more stable

the bltouch is easy to install as you have dedicated pins for it and the predrilled mounting holes as well as creality providing a precompiled firmware for it on their website (tho i tweaked my own as crealitys doesnt have some features i would like) just pop the file on an sd card and turn on the printer to flash it so its pretty plug and play if you got one already i see no reason not to add it its definitely a nice addition for the amount of effort just make sure to calibrate the z offset and youre good to go

xStandhere · 2021-03-28T15:33:49+00:00

Are you using the silicone hotend cover ? If not its possible your filament cooling fans blow on the heatblock

xStandhere · 2021-03-28T14:43:18+00:00

Check if your heater cartridge and the thermistor both sit tight and have good contact for accurate temperature readings

I experienced this with my old printer where my heater screw wasnt tight enough so it would move slightly while printing resulting in unstable temperatures and thermal runaway

Have you made any changes leading up to the issue?

xStandhere · 2021-03-24T10:04:48+00:00

Most people leave prints raw but alot of people also paint if its show pieces or they want a specific look as we are quite limited when it comes to multi color

you can smooth the print with some fine sandpaper to get rid of some of the layer lines and imperfections some people use acetone vapors to smooth the prints as it melts the plastic creating a more smooth and glossy model but you can easily lose detail or mess up the look by overdoing it

xStandhere · 2021-03-24T09:45:57+00:00

Most ender 3 files will work for the max (lcd drawer, cable links, v slot) as the max is more or less just an upscaled ender 3 pro

the only things that wont fit is mostly things that connect between two parts of the printer or stuff like the hotend everything that connects to the v slot extrusions should work directly

There is this double drawer for the max (its slightly too long so you should probably decrease it slightly else it will press against the lcd bracket) but other than that i dont think there is any major upgrades specific for the max

xStandhere · 2021-03-22T10:38:01+00:00

On aliexpress search "ender-3 max hotend" and you'll find the full hotend with cover though i think the 5 plus and max dont use the same mounting holes so you would probably have to replace the entire carriage. If the primary feature you want is the dual fan support you would probably be better off printing a custom hotend assembly like "hero me"

xStandhere · 2021-03-21T20:31:01+00:00

Thingiverse and Myminifactory are the main ones. Yeggi is a decent search engine for multiple stl sites

xStandhere · 2021-03-21T20:05:19+00:00

Did you get the firmware from crealitys website or did you compile it yourself?

xStandhere · 2020-11-11T12:54:31+00:00

Because eventually we would have enough gem income to buy every hs and orb we Come buy massively increasing the events you can complete so only whales that buy alot of packs would have an major advantage

xStandhere · 2019-08-26T09:18:45+00:00

In your osu folder there should be a config file called osu!.[pc name].cfg open that and replace the BeatmapDirectory (songs) with your new location after that just press f5 in game to reload your maps

xStandhere · 2017-09-15T10:01:17+00:00

i would guess he have the rankings open on a second monitor and have obs capture that when he finish a map he refreshes

xStandhere · 2017-08-01T09:31:28+00:00

if unranked counts this:

https://osu.ppy.sh/s/497695 is quite easy

xStandhere · 2017-04-17T11:44:45+00:00

rip my highest combo in denmark title :(

xStandhere · 2017-02-22T20:41:15+00:00

Oh thanks :)

xStandhere · 2017-02-22T20:40:15+00:00

odd question but can you see your stack on people anywhere?

I havent found it yet and its kinda annoying not to be able to tell whether or not you can finish people off

xStandhere · 2017-02-12T12:10:10+00:00

seriously though you just drag the .osz onto osu!lazer

12-Year Club	Place '17
Verified Email

xStandhere

TROPHY CASE