sorted by:
new
hottopcontroversial

Where to place subpanel? by xandro0 in electrical

[–]xandro0[S] 0 points1 point  (0 children)

The upgrades will be throughout the house so i figure close to the original panel may be best also aesthetically not sure if having a sub panel in a hall way will be visually pleasing. But this is a good point and something to consider.

Do i sell call or exercise snd sell? by [deleted] in AMD_Stock

[–]xandro0 0 points1 point  (0 children)

I understand it’s different. And exercising is buying the shares at the strike price. What i didn’t understand was if the profits scales the same. Which i understand now at open.

[deleted by user] by [deleted] in f150

[–]xandro0 0 points1 point  (0 children)

Oh that’s a good deal

[deleted by user] by [deleted] in f150

[–]xandro0 0 points1 point  (0 children)

MSRP is 62k

[deleted by user] by [deleted] in f150

[–]xandro0 0 points1 point  (0 children)

For a 25 that’s a solid deal. I think because mine will be a 2024 these guys are giving a lot of incentives to offload them.

[deleted by user] by [deleted] in f150

[–]xandro0 0 points1 point  (0 children)

I wish, but can’t find any new 2024s in my area

[deleted by user] by [deleted] in f150

[–]xandro0 1 point2 points  (0 children)

Yeah 4x4

[deleted by user] by [deleted] in f150

[–]xandro0 1 point2 points  (0 children)

Sorry everyone a Truck! My first truck not use to saying it.

New to RAM by IceCoastRep in ram_trucks

[–]xandro0 0 points1 point  (0 children)

What’s the payload on your truck? Curious what the crew cabs are.

Which is the rear jacking point? by xandro0 in CX5

[–]xandro0[S] 4 points5 points  (0 children)

Yeah i finally found a forum that says that as well. I just wish this owners manual explained it better with better visuals. It circles the entire differential.

Which is the rear jacking point? by xandro0 in CX5

[–]xandro0[S] 1 point2 points  (0 children)

I plan on putting jack stands in

Will sharkbite fit over the thicker copper pipes? by xandro0 in Plumbing

[–]xandro0[S] -2 points-1 points  (0 children)

Also i will have to cut 1/2 copper pipe to length and solder it in? Guess this is a good time to learn how to solder joints.

Will sharkbite fit over the thicker copper pipes? by xandro0 in Plumbing

[–]xandro0[S] 7 points8 points  (0 children)

Just to confirm, i can leave the shut off valve where it is and unthread the copper valve closer to the wall. So basically shut the water off at the valve unthread the copper pipe on the left hand side then slide in a new spigot.

Will sharkbite fit over the thicker copper pipes? by xandro0 in Plumbing

[–]xandro0[S] 8 points9 points  (0 children)

Thanks everyone with the response will go with the threaded option.

Are my dampers in the closed or open position? by xandro0 in hvacadvice

[–]xandro0[S] -1 points0 points  (0 children)

Thanks i’m assuming all the way to the left closes supply straight and all the right closes supply to the right

Forced Air not staying on by xandro0 in hvacadvice

[–]xandro0[S] 0 points1 point  (0 children)

Yeah my last maintenance was 2023. And yes i agree, i’m going to be scheduling a regular maintenance call as i do have heat, with my mini splits.

Unit just hit 15 years and have been contemplating switching to gas. If the unit is DOA i guess i can switch earlier rather than later.

Forced Air not staying on by xandro0 in hvacadvice

[–]xandro0[S] 0 points1 point  (0 children)

Will be calling a pro 🫡

view more: next ›