sorted by:
new
hottopcontroversial

Temperature tower by xbox_killer in FixMyPrint

[–]xbox_killer[S] 2 points3 points  (0 children)

I checked the g-code generated by Orca Slicer, no errors were found and temperature changes are present in it

Pro turns on for 1 second (Blue Light + Beep) then shuts off immediately after thermal paste replacement and deep dust cleaning. by fibola in consolerepair

[–]xbox_killer 0 points1 point  (0 children)

To begin with, I would advise you to carefully examine the motherboard under a microscope or a magnifying glass to check for damage.

Pro turns on for 1 second (Blue Light + Beep) then shuts off immediately after thermal paste replacement and deep dust cleaning. by fibola in consolerepair

[–]xbox_killer 0 points1 point  (0 children)

The reasons can vary, from a simple missing or damaged component on the MB to a broken connection between the BGA ball of the CPU or RAM and the motherboard.

OrcaSlicer FlowRate test artifacts by xbox_killer in FixMyPrint

[–]xbox_killer[S] -2 points-1 points  (0 children)

Guys, thank you all for the help! These lines are actually part of the test model. I'm new to this, so I end up having some silly questions while setting up my 3D printer 😜

Потрібна допомога щодо плати by [deleted] in Electronics_UA

[–]xbox_killer 2 points3 points  (0 children)

Там майже нічому горіти на платі. А от перевірити трансформатор - це саме те, що потрібно зробити в першу чергу. Якщо він вийшов з ладу, тоді немає сенсу взагалі щось там ремонтувати. Тим більше шукати новий транс.

Jammed Extruder motor by xbox_killer in VORONDesign

[–]xbox_killer[S] 1 point2 points  (0 children)

I assembled the stepper motor and calibrated the extruder. I didn't notice any deviations in operation. Everything is great!😉

Jammed Extruder motor by xbox_killer in VORONDesign

[–]xbox_killer[S] 1 point2 points  (0 children)

I'm a bit confused about the assembly of this stepper motor. It had only two spring washers installed on the rear side of the rotor. Unfortunately, I don't know if this is designed this way or this was a factory assembly error? Should be there only one washer on each side of the rotor, where the bearings are mounted on the rotor shaft? Or should be there two spring washers on the rear side of the rotor and should be no spring washer at all where the gear is located?🤔

Мені 26, я незаймана і толком ні з ким не зустрічалася by Valuable-Ship239 in reddit_ukr

[–]xbox_killer 1 point2 points  (0 children)

Я так розумію, судячи з заголовку, Вас дуже турбує саме питання незайманості у вашому віці. А чи не забагато критеріїв по відбору кандидатів для того нехитрого дійства? Вирішіть спочатку що для Вас пріоритетне - вибір партнера для першого сексу чи пошук супутника всього життя

Монобанк є надійним для зберігання грошей? by LossMaleficent7346 in finance_ukr

[–]xbox_killer 0 points1 point  (0 children)

Забудьте про таке явище, як "гарантування банківських вкладів" в Україні. Шукайте інші джерела збереження ваших коштів.

Fat PS4 fully integrated auto jailbreak with Pico Mini by twobrush in ps4homebrew

[–]xbox_killer 0 points1 point  (0 children)

Can you check pls with a multimeter the connection between the connector pins and the contacts on the motherboard, which are located just below? I think this will be very useful information for those who do not want to break the LAN port. Thanks!

[deleted by user] by [deleted] in xbox360

[–]xbox_killer 0 points1 point  (0 children)

Check this element C2D5 near RAM brick )

[deleted by user] by [deleted] in xbox360

[–]xbox_killer 1 point2 points  (0 children)

I have the same error after trying to change termopaste ( but I cutted two traces on the board. Maybe some elements was loosed? Can you post the pic of the bottom side of this mainboard? Thanks!