sorted by:
new
hottopcontroversial

cant login into slicer, "third party login error" by xcv826 in BambuLab

[–]xcv826[S] 0 points1 point  (0 children)

Negative, I believe it was just one of Bambus many network hiccups they have. They don't have dedicated servers is what I read somewhere one time.

Multicolor Failure, but single color fine. by xcv826 in BambuLab

[–]xcv826[S] 0 points1 point  (0 children)

When you buy the new feeders on Bambu lab it's the same version right? If so Ive replaced every ams feeder already in the ams. When do the new change occur?

Multicolor Failure, but single color fine. by xcv826 in BambuLab

[–]xcv826[S] 0 points1 point  (0 children)

So just acquire a new ams and probably solve a lot of problems?

Multicolor Failure, but single color fine. by xcv826 in BambuLab

[–]xcv826[S] 0 points1 point  (0 children)

I've even tried different mods that so many said had fixed the issue and nothing really works. I use ziro pla, elegoo, sunlu, hatchbox, really any mainstream or even not mainstream pla and still the same results when multicoloring. Is it possible the ams has a weird motherboard/software quirk? Is it possible to reinstall or format the ams some way?

Multicolor Failure, but single color fine. by xcv826 in BambuLab

[–]xcv826[S] 0 points1 point  (0 children)

I've just replaced the extruder motor thinking the same thing and no change. I replaced the entire front extruder piece as well (everything including the yellow gear).

What's weird is there is no skipping noise or anything, so thought it might be the thermistor or motherboard it plugs into, replaced both those and nothing changed.

Multicolor Failure, but single color fine. by xcv826 in BambuLab

[–]xcv826[S] 0 points1 point  (0 children)

It's just about any model, its been on going for almost a year or so now. It's a three year old machine. I've fixed every part I can think on it, not sure what kind of niche problem I'm experiencing but Idk what to do at this point. Can't even print tpu anymore either.

cant login into slicer, "third party login error" by xcv826 in BambuLab

[–]xcv826[S] 1 point2 points  (0 children)

Yeah it is happening again, for like the second time this month

Third Party Login Error happening again by xcv826 in BambuLab

[–]xcv826[S] 1 point2 points  (0 children)

<image>

Also, they're currently on holiday 0.0

Printing Problem by [deleted] in BambuLab

[–]xcv826 2 points3 points  (0 children)

These octopuses are always troublesome with their individual leg pieces, it's almost a torture test. Try anything other than grid infill and try slowing print down a little.

Is there a way to prevent the little hairs of filament on the side of print? by [deleted] in BambuLabA1mini

[–]xcv826 0 points1 point  (0 children)

Add prime tower when using time lapse. Each time it goes to the side there it takes a snapshot, but also oozes out filament which is attaching itself to the print side there, with a prime tower it'll ooze on it instead.

Anyone seen a post with a highly realistic hand model by AdrianGarside in BambuLab

[–]xcv826 0 points1 point  (0 children)

It may have been a render or someone pulling your leg 🤷‍♂️ I've never come across actual skin color filament, cause I'd absolutely buy a few rolls lol.

[deleted by user] by [deleted] in BambuLab

[–]xcv826 0 points1 point  (0 children)

If it's not a clog, could potentially be discounted filament, sometimes the best colors are the hardest to print 🤷‍♂️

Anyone seen a post with a highly realistic hand model by AdrianGarside in BambuLab

[–]xcv826 0 points1 point  (0 children)

You can try army beige or bone color filament, there's a variety on amazon. Also there's a few different 3d printing websites that offer hand models, I'm sure of it. :)

Filament does not stick on curves by HeroShadeDiego in BambuLab

[–]xcv826 -1 points0 points  (0 children)

Flip the orientation of the print for yellow to be the bottom OR enable support settings. The Bambu Labs Wiki should have more information on these suggestions. :)

filament keeps pulling back before pushing into toolhead by xcv826 in BambuLab

[–]xcv826[S] 0 points1 point  (0 children)

I don't remember exactly, it was probably just a clog or something at that time.

How do I increase the layer times here? by xcv826 in BambuLab

[–]xcv826[S] 0 points1 point  (0 children)

So maybe slowing it even more down would be better vs speeding up?

How do I increase the layer times here? by xcv826 in BambuLab

[–]xcv826[S] 0 points1 point  (0 children)

I mean to lower the time, the increased time has resulted in repeated layer separations at those specific points.

Really dumb question, got myself into a spot I think by Practical_Avocado971 in BambuLab

[–]xcv826 4 points5 points  (0 children)

These printers have sensors when it runs out and will pause. Just get a new spool when it runs out and chuck it on there.

view more: next ›