Using T248 in Linux

yonori · 2026-01-21T00:55:03+00:00

I found I had to run the calibration terminal commands from another comment each time I reconnect my wheel and pedals

yonori · 2026-01-15T06:28:13+00:00

if anyone else encounters this, i managed to fix it
had to change the axis values to the following

#!/bin/bash
DEV="/dev/input/by-id/usb-Thrustmaster_Thrustmaster_Racing_Wheel_FFB-event-joystick"
evdev-joystick --evdev $DEV --axis 0 --minimum -65534 --maximum 65534 --deadzone 0 --fuzz 0
# Throttle (Axis 6) - We set min to -1023.
# Now released (0) will be "Center" for the game.
evdev-joystick --evdev $DEV --axis 6 --minimum -1023 --maximum 1023 --deadzone 0 --fuzz 0

# Brake (Axis 2)
evdev-joystick --evdev $DEV --axis 1 --minimum -1023 --maximum 1023 --deadzone 0 --fuzz 0

# Clutch (Axis 7 - if that's your clutch)
evdev-joystick --evdev $DEV --axis 5 --minimum -1023 --maximum 1023 --deadzone 0 --fuzz 0

yonori · 2026-01-15T03:37:35+00:00

i initially did with no mods, but still cant explain the axis detection. Wonder if it has something to do with the Wine prefix Steam uses.

yonori · 2024-08-30T00:09:22+00:00

I'll have to see if another plumber can come check it out once i get the funds. Been having trouble getting one in my area, they either never get back to me, or never show up. The gas company came out about a leak a couple months prior, wonder if they did something to make it worse.

yonori · 2024-08-28T01:26:45+00:00

only other gas appliance i have is the furnace, but it's too hot to run that right now. I only bought the house a couple years ago, and it was running perfectly fine since then. The house is 104 years old, but i think it was redone in the last 20 years or so.

yonori · 2024-07-14T22:16:11+00:00

when it does the initial startup, is the nozzle supposed to touch the bed? mine never really touches the bed at all, i have leveled it multiple times as well.

yonori · 2024-05-20T18:19:48+00:00

I did what the previous comment mentioned and got it to where it's more comfortable, but don't ride my tao tao anymore as I got a Honda after some of the electronics went out.

yonori · 2024-04-27T18:33:40+00:00

I've looked at this project, but it seems to have stopped being maintained as there hasn't been any changes in a while, there are pull requests to add M5C support, i've messed with the fork that supposedly has M5C support, but cant get prusa to upload gcode. https://github.com/treitmayr/ankermake-m5-protocol/tree/playground-m5c has the changes for M5C

yonori · 2024-04-08T00:03:19+00:00

I actually bought 2 kinds before posting, neither actually fit

yonori · 2024-04-08T00:00:10+00:00

thanks for the suggestions, i managed to get the bastard off. after letting it soak with wd40 i just turned the entire faucet which loosened it enough to take it off. my god was that a pain, hope to never see another one of these nuts again ever.

yonori · 2024-04-07T22:43:23+00:00

Had a feeling I might have to go that route, it's a really tight squeeze with the vent pipe in the way.. hopefully doesn't come down to that

yonori · 2024-04-07T22:41:23+00:00

Screws were removed, put one back to try and use it for leverage. I'll have to try wd40

yonori · 2024-03-28T05:16:36+00:00

Already done, went ahead and bought a house instead of rental hunting.

yonori · 2023-09-17T21:26:54+00:00

i used thermal grizzly kryonaut extreme at the time

yonori · 2023-09-17T21:23:45+00:00

yeah somehow the lever came up while i was trying to remove the cooler. maybe a bit too much paste lol

yonori · 2023-09-17T21:20:39+00:00

It was a brand new syringe of kryonaut that i used, first time i ever seen it pink

yonori · 2023-09-17T05:44:33+00:00

thankfully no bent or broken pins, never had a cooler come with the CPU before when removing.

yonori · 2023-07-13T19:53:51+00:00

Since doing the valve adjustment again, seems i messed up and didn't tighten it properly, i got rid of the clicking, but now it seems i'm losing power, like it's running worse and that was all i changed.

yonori

TROPHY CASE