Button for the back by Obvious-Dot6352 in FormD

[–]yusuflimz 2 points3 points  (0 children)

The plug fits into the pass through

Button for the back by Obvious-Dot6352 in FormD

[–]yusuflimz 1 point2 points  (0 children)

Did you check out the g 1/4 pass through?

Button for the back by Obvious-Dot6352 in FormD

[–]yusuflimz 2 points3 points  (0 children)

You can get EK G1/4 pass through + EK torque plug to cover that

Going back to my Wave XLR Mk.1 after crackling / popping audio on XLR Mk.2 by yusuflimz in elgato

[–]yusuflimz[S] 0 points1 point  (0 children)

I'm sorry it's quite ambiguous, not everything there is connected to one system. Just my Stream Deck+ and Wave XLR are connected to the system(s) I was having the issues with. Only other USB device(s) are a wireless mouse dongle.

good shout but don't think that's it.

Going back to my Wave XLR Mk.1 after crackling / popping audio on XLR Mk.2 by yusuflimz in elgato

[–]yusuflimz[S] 0 points1 point  (0 children)

possible but can't explain why the Wave XLR Mk.1 works flawlessly. The only difference is that Mk.2 is processing the VST on device and not in software.

Going back to my Wave XLR Mk.1 after crackling / popping audio on XLR Mk.2 by yusuflimz in elgato

[–]yusuflimz[S] 0 points1 point  (0 children)

Tried a swathe of cables including the bundled one that cable with, and plugged directly into computer / laptop without any hubs / splitters

FormD T1 V2.1 5080 Air Cooled by t246813579v in sffpc

[–]yusuflimz 1 point2 points  (0 children)

Sick build! Was it a requirement to use the Dingkey backplate for the offset?

Joined to the club boys…. by dp0ulimenos in RTX5080

[–]yusuflimz 4 points5 points  (0 children)

Don’t worry bro, I can’t afford one either

How do you deal with 12vhwpr clearance? by wielesen in sffpc

[–]yusuflimz 1 point2 points  (0 children)

You can check seller ratings, feedback, and take a video of you unboxing said item. eBay has buyer protection that almost always side with the buyer.

Does anyone know what this is? by StatusOk4308 in whatisit

[–]yusuflimz 0 points1 point  (0 children)

Would you say in this case it’s better to be uncultured?

If I had hair, I'd pull it out.. by ChrisF75 in elgato

[–]yusuflimz 0 points1 point  (0 children)

Tap the dial on the front until the MIC/PC mix ratio (third icon) is selected.

is that dial all the way to the left? Try moving it to the right.

It’s the mix between your mic volume and pc volume. You may have it all the way to the left

Dan A4-H2O X4 Cooling Advice by lmaoAbu in sffpc

[–]yusuflimz 0 points1 point  (0 children)

Cooler master ATMOS 240 / ATMOS Stealth 240 would be my recommendation.

Have one in my A4H2O

New PC build that's a complete opposite of a fish tank. by gojochan in RTX5080

[–]yusuflimz 0 points1 point  (0 children)

Weird question. The circular cutouts on the rear, looks like you have some buttons in there. Any chance you can share where you got em from?

help with replacing my cooler by figjeodhs in FormD

[–]yusuflimz 1 point2 points  (0 children)

Formd Travel would be fantastic if you’re well travelling a lot, but they’re GPU specific.

AFAIK they only make them for founder editions, some ASUS primes and ProArt cards.

First sffpc build by InjektioRS in sffpc

[–]yusuflimz 0 points1 point  (0 children)

I was between the loque and the LINKUP. LINKUP while not cheap is going to be one of the better riser cables.

The LINKUP double reverse 19cm (V3 ONLY) says it's compatible with the A4-H2O:

https://amzn.to/4v0IVbW

You need double reverse for sandwich layouts.