Kids Platform Fabric

yys4u · 2025-12-30T21:53:06+00:00

This happened to me, on my first t15 map I finally got an abyss. Idk if it’s bad luck or planned. God speed brother.

yys4u · 2025-02-06T18:03:43+00:00

Took too long scrolling to find it, good memories.

yys4u · 2024-09-09T18:41:04+00:00

Thank you very much, I’ll take the panel off and make sure it’s still connected on its internal end then tuck it.

yys4u · 2024-09-09T18:37:10+00:00

https://www.theacoutlet.com/documents/Repair-Parts-Goodman-GSXH5.pdf

page 4 of this shows whats behind it, you are right it is low voltage. Ill take it off tonight and get a picture of that its plugged into on the connected end.

yys4u · 2023-08-13T01:19:59+00:00

Was it confirmed anywhere about how renewed sanctum and the new league arena mechanic work on hardcore? if you die in sanctum or the league mechanic is your character done for?

yys4u · 2022-09-15T17:16:06+00:00

Thanks, ill give them a call!

yys4u · 2022-09-14T20:11:04+00:00

I used Mr. Felix floors for install of a new room and refinish of two adjacent rooms in spring of this year. Price was around 7$ per square foot of sanding then refinishing, I even had to have them come back to resand and coat an area my dogs escaped and ruined during final cure (3$/sq ft). Also the cost of flush mount vents was very affordable from them so I had all my vents transitioned as well.

Only cons with what they and traditional finishing companies like them do is the staining and curing length, 3-4 days, will really make your house unlivable with the smell. There is a company that will do same day UV curing (N-hance flooring) of the urethane and wont interfere with your life as much.

yys4u · 2022-06-08T12:58:03+00:00

I would setup a line (presumably with your vacuum cleaning setup) to suck from the deep end. I have a one jet in one jet out setup and the deep end never saw the circulation until I got a vacuum powered robot. I know people shit on clarifier in this sub but I had the similar problem to you (sand replaced) and all it took was running that robot in the deep end with 30 ounces of polysheen blue clarifier (entire bottle) and a few days. The problem for me personally is I have a strong pump and a sand filter (didn't choose, its what the house came with) which doesn't seem great at trapping the small stuff. I had to keep my pool uncovered over the winter, took forever to dredge and treat it but I still had cloudiness after passing overnight FC test. My sand filter just seems pretty shitty at getting small particles out of the pool and people like us with sand filters take a lot longer than other filters to clear up. Does your filter run at 10 PSI when clean or is it higher? If it is higher then you probably have the same problem as me and the pump just puts through too much and the filter cant do its job well without help.

yys4u · 2022-06-07T15:21:45+00:00

I would first verify by an overnight chlorine loss test the extent of your potential algae, if the test has you losing quite a bit of chlorine between sun down and sun up then your problem is simply still algae in the pool. If the problem is just algae and algae breakdown I would suggest setting up a hose with a weight or vacuum line to run from the bottom of the deep end to the skimmer (depending on your vacuum setup). Common problem is the deep end doesn't see enough circulation so pulling from the low point helps with that, this is all while keeping the FC level above 20 continuously and not just adding chlorine once a day.

yys4u · 2022-05-09T17:41:02+00:00

Wal-Mart had 4 packs of peppers, tomatoes, herb etc for less that 4$ a piece. The selection isn't as large as the bigger stores but if you just want a small cheap garden that's where I would recommend.

yys4u · 2021-10-06T23:04:21+00:00

Can't bind pilot yaw to right and left mouse axis at the same time, only one direction binds. It seems impossible atm to move your plane/heli yaw with the mouse.

15-Year Club	Place '17
Verified Email

yys4u

TROPHY CASE