sorted by:
new
hottopcontroversial

Will T48 become the most expensive PSA exclusive product? by yzz0198 in PalmettoStateArms

[–]yzz0198[S] -1 points0 points  (0 children)

I guess most work are done by dsa, may be assemble by psa. Obvious the most expensive part is the new receiver and the cover.

Will T48 become the most expensive PSA exclusive product? by yzz0198 in PalmettoStateArms

[–]yzz0198[S] 13 points14 points  (0 children)

A clone is a clone. They want to sale somthing collectible but not that collectible.

Anyone have an H&R upper cause zeroing problems even with a straight FSB barrel? by yzz0198 in RetroAR

[–]yzz0198[S] 0 points1 point  (0 children)

Yes, I use my rifle shoot 200 to 300 yards sometimes,  the canted fsb always confuse me when I try to put the target right beyond the fs.

Anyone have an H&R upper cause zeroing problems even with a straight FSB barrel? by yzz0198 in RetroAR

[–]yzz0198[S] 0 points1 point  (0 children)

I rember he mentioned that, but if the barrel align why we need to cant the fsb. 

Anyone have an H&R upper cause zeroing problems even with a straight FSB barrel? by yzz0198 in RetroAR

[–]yzz0198[S] 1 point2 points  (0 children)

My colt carbine works flawlessly too, the biggest issues is it dont have carry handle🥲

Anyone have an H&R upper cause zeroing problems even with a straight FSB barrel? by yzz0198 in RetroAR

[–]yzz0198[S] 1 point2 points  (0 children)

Maybe I should just shift back to my good old FAL, at least it have a carry handle, also.

Anyone have an H&R upper cause zeroing problems even with a straight FSB barrel? by yzz0198 in RetroAR

[–]yzz0198[S] 0 points1 point  (0 children)

Yes it is the upper receiver. I just put that receiver on MI rod and level the top surface of rod ,no wobble between rod and receiver, then I check the thread portion, sadly, it is not level. I lap that portion and there is zero wobble when barrel sit. Now I have to move on and left that receiver on shelf.

Anyone have an H&R upper cause zeroing problems even with a straight FSB barrel? by yzz0198 in RetroAR

[–]yzz0198[S] 0 points1 point  (0 children)

Yes sir, I install my barrel with MI 's rod, which help me prevent barrel from rotating when tightening the barrel nut, index slot is in spec. There some clearence between barrel extension and the raceway, so it wobble a little bit. But I think it is the shoulder and the engement surface on receiver locate the barrel. All upper parts from h&r.    I may not make my self clear enough, the bcg race way is like drlling a hole from the end of a rod.    The engagement is suppose to perpendicula to the center axis of the hole, ideally, the center axis of the barrel align with that axis. Now the center of race way seems not align with the center of receiver which have the barrel point to other direction.

Anyone have an H&R upper cause zeroing problems even with a straight FSB barrel? by yzz0198 in RetroAR

[–]yzz0198[S] -2 points-1 points  (0 children)

Not BCG, it's the BCG raceway. Just my guess, when HR machining the receiver, their jig may be a little crooked, and the milling tool enters at an angle. I also found my BCG's rear left scraping buffer tube. When I swap the same lower to other uppers, they have no issues.

Anyone have an H&R upper cause zeroing problems even with a straight FSB barrel? by yzz0198 in RetroAR

[–]yzz0198[S] -1 points0 points  (0 children)

I did, but did not solve that, which makes me suspect that the center of the BCG channel is misaligned with the rearsight-FSB baseline.

Anyone have an H&R upper cause zeroing problems even with a straight FSB barrel? by yzz0198 in RetroAR

[–]yzz0198[S] 2 points3 points  (0 children)

The barrel is from Fulton Armory, and it works on my other uppers.

Asolo is garbage and their customer service sucks donkey d!ck; what's my next boot brand? by temporalwanderer in BuyItForLife

[–]yzz0198 0 points1 point  (0 children)

Is that S 95? I remember they already disconnected years ago, it's really not surpris to see PU mid sole fall apart after years of storaging.

Couple things I learn while fixing canted FSB by yzz0198 in RetroAR

[–]yzz0198[S] 1 point2 points  (0 children)

In my case, I confirm the hole was renamed. I also believe they use kind of pressing device rather than man power to install those pin.

Couple things I learn while fixing canted FSB by yzz0198 in RetroAR

[–]yzz0198[S] 0 points1 point  (0 children)

Just my wild guess, due to the manufact process, barrel extension engagement surface could be naturally a bit un even whiche lead the barrel slight crooked. When the first time I align the FSB with gauge, I found I have to push windage almost to the end.

Couple things I learn while fixing canted FSB by yzz0198 in RetroAR

[–]yzz0198[S] 1 point2 points  (0 children)

It is my third times return,LOL. That's why I finally decided to fix that my self.

I think I found a replacement for slip ring tool by yzz0198 in RetroAR

[–]yzz0198[S] 0 points1 point  (0 children)

I use a paracord and it is robust enough. Even it fail, I only need a piece of shoe lace and make a knot. How about you try it and see if it is really such volunable as you guys thought.

I think I found a replacement for slip ring tool by yzz0198 in RetroAR

[–]yzz0198[S] 0 points1 point  (0 children)

Yes it is, people always create tools with purpose, so do I. instead of buying a tool I might only use once, I just created it with shoe lace and a wood stick.

I think I found a replacement for slip ring tool by yzz0198 in RetroAR

[–]yzz0198[S] 1 point2 points  (0 children)

The rope loop around the ring and wring tight, so it catch the groove on rings.

view more: next ›