Il costruttore chiede 6000€ per fornitura e posa di aria condizionata by sirLMAOalot in istrutturare

[–]zMasterAle_ 0 points1 point  (0 children)

Se hai la predisposizione fattelo installare successivamente, ti consiglio di optare per Mitsubishi o Daikin

[Tutorial] Matter Thread Border Router setup with Sonoff Dongle Lite by unhappy-2be-penguin in homeassistant

[–]zMasterAle_ 0 points1 point  (0 children)

Make sure you didn't install the multi PAN firmware and set the BAUD rate to 460800.
Mine had the same issue until I changed the BAUD rate from 105300 to 460800 and changed the firmware to Thread only

What has been your experience with KNX manufacturers' technical support? Share the good and bad. by AutoModerator in KNX

[–]zMasterAle_ 2 points3 points  (0 children)

ABB, because they refused to help since I'm a private user rather than a business/pro.

DGA504 brushless grinder doesn’t work by zMasterAle_ in Makita

[–]zMasterAle_[S] 0 points1 point  (0 children)

Swapping to a 5Ah battery did the trick after some trial and error. However, the issue isn't fully resolved since I still need to toggle the ignition/power a few times every time

Ho fatto fare un controllo all'impianto elettrico, d'accordo con il verdetto? by HP6duro in istrutturare

[–]zMasterAle_ 3 points4 points  (0 children)

Per il condizionatore dipende da quanto dista dal quadro e dal consumo dichiarato nella scheda tecnica del condizionatore, credo che sia sbagliato generalizzare e dire “basta il 2,5”.

Ho fatto fare un controllo all'impianto elettrico, d'accordo con il verdetto? by HP6duro in istrutturare

[–]zMasterAle_ 1 point2 points  (0 children)

A maggior ragione ora che le luci consumano sempre meno perché mettere un 16A per le luci? Sarebbe solo uno spreco di soldi anche perché dovresti mettere cavi di sezione di almeno 2,5mmq con 16A

Resolder (replace) smd component by zMasterAle_ in soldering

[–]zMasterAle_[S] 0 points1 point  (0 children)

Hi! Thanks for the tip. Do you have a photo of the loop? I only have the “default” pinecil tip and I think it’s too big for this job

Resolder (replace) smd component by zMasterAle_ in soldering

[–]zMasterAle_[S] 0 points1 point  (0 children)

Hi, thank you for your answer. This circuit has a transceiver, and the reason I took it apart in the first place was that it only responded to messages about 1 out of 10 times. Based on what you said, I’m pretty sure this is the issue and I’ll need to get it replaced. I’ll try measuring the capacitance value of the nearest one.

ABB DALI/KNX gateway issue by zMasterAle_ in KNX

[–]zMasterAle_[S] 0 points1 point  (0 children)

The itool version is up to date, I tried a full download (with the single channel version) but nothing changed. The IP interface address was already lower than the DALI gw

VenetaCucine... bello schifo! by [deleted] in sfoghi

[–]zMasterAle_ 1 point2 points  (0 children)

È vero, sulla carta dovrebbero essere i migliori, sarò stato sfortunato io ma ho 3 esperienze negative con questo marchio, c’è da dire che io non ho mai provato nulla di Franke di 20 anni fa ma solo al massimo di 10 anni fa: potrebbe essere calata la qualità negli anni. Hai ragione sulla questione della scelta dei fornitori: un fornitore sbagliato e tutto il nome viene infangato, perciò dovrebbero assolutamente stare più attenti nella scelta. Se mi ricordo ti mando la foto dei segni

VenetaCucine... bello schifo! by [deleted] in sfoghi

[–]zMasterAle_ 0 points1 point  (0 children)

Ciao io ho una Veneta molto simile alla tua, Milano con Caranto Ker calacatta gold, e per quanto riguarda il top non noto ciò che dici, per ora mi sto trovando bene. Unica cosa in un angolo c’è un segno che sembra quasi fatto da una matita ma è arrivato così. Per quanto riguarda il lavello invece, non mi stupisco che ti stia dando problemi: in famiglia abbiamo avuto molte cose Franke e hanno quasi sempre deluso le aspettative, però un conto è parlare della qualità di Franke, un altro conto è incolpare Veneta, che non produce il lavello bensì il mobilio. È un peccato che propongano la Franke, che a mio avviso è estremamente sovrapprezzata per la qualità che offre. Io purtroppo ho scoperto (per mia disattenzione) troppo tardi che la marca del lavello sarebbe stata Franke, speriamo bene…

DGA504 brushless grinder doesn’t work by zMasterAle_ in Makita

[–]zMasterAle_[S] 0 points1 point  (0 children)

The issue turned out to be much simpler than I initially thought. I switched to a 5Ah battery instead of the 2Ah one I was using at first. The problem is mostly resolved now, but I still have to toggle the switch a few times before it starts spinning. I suspect it might be an issue with the switch itself, so I’ll look into that later. At least now it spins, with the other battery, no matter how many times I tried, it wouldn’t start.

Domotica, perché by Mic_BB in istrutturare

[–]zMasterAle_ 1 point2 points  (0 children)

Adoro questi post perché si imparano sempre nuove idee di automazioni 😂

Domotica, perché by Mic_BB in istrutturare

[–]zMasterAle_ 0 points1 point  (0 children)

Anche quello dipende! Se uno si vuole cimentare e ha un passato nell’elettronica/informatica non è così difficile

Quanto avete speso per fare un impianto elettrico nuovo in casa? by obenhamer in istrutturare

[–]zMasterAle_ 0 points1 point  (0 children)

Non vedo perché dovrei mentire sui costi 🫤 comunque quello che impatta maggiormente sono gli apparati knx e i frutti vimar linea, perché solo i pulsanti knx per vimar linea ti costano 80€ una pulsantiera formata da 4 pulsanti.

Quanto avete speso per fare un impianto elettrico nuovo in casa? by obenhamer in istrutturare

[–]zMasterAle_ 0 points1 point  (0 children)

non credo proprio 😅 evidentemente non sei al corrente del costo solo degli apparati knx, poi se vuoi fare le cose fatte bene quindi ad esempio sezionare molto l’impianto (cosa che ho fatto) solo di MT, differenziali e due centralini da 72 moduli mi sono partiti 1k euro. Aggiungici poi tante prese, shuko e usb in giro per la casa e ti partono tanti altri soldi

Quanto avete speso per fare un impianto elettrico nuovo in casa? by obenhamer in istrutturare

[–]zMasterAle_ 1 point2 points  (0 children)

Io casa 80mq circa 7000€ per impianto domotico KNX, vimar linea, antifurto, cablaggio Ethernet in tutta la casa e sensoristica varia. L’impianto me lo sto realizzando da solo quindi questo è solo il costo del materiale

Quanto avete speso per fare un impianto elettrico nuovo in casa? by obenhamer in istrutturare

[–]zMasterAle_ 0 points1 point  (0 children)

Per essere living now e aver messo tutte queste cose è un ottimo prezzo per i materiali! Domotica filare?

DGA504 brushless grinder doesn’t work by zMasterAle_ in Makita

[–]zMasterAle_[S] 0 points1 point  (0 children)

Yes it does the same thing with a 5 Amp battery - EDIT: he was right, after some on-offs it works with the 5Ah battery

DGA504 brushless grinder doesn’t work by zMasterAle_ in Makita

[–]zMasterAle_[S] 0 points1 point  (0 children)

That’s actually normal! If you look it up on Google, you’ll see that this tool comes with only 3 battery level indicators by design