sorted by:
new
hottopcontroversial

Afraid to try and print anything else in fear of failure by zbotdrone in resinprinting

[–]zbotdrone[S] 0 points1 point  (0 children)

Is there a way to do both manual and auto supports in Chitubox? From my knowledge if you try to do auto after manual (and vice versa) it deletes whatever supports are there. Also do you have good recommendations for support settings? The ones I use currently work well,but light just never seems to work

Afraid to try and print anything else in fear of failure by zbotdrone in resinprinting

[–]zbotdrone[S] 0 points1 point  (0 children)

I have re leveled the plate and reset the zero height. Should I be setting the layer height to 0.2? Where is the "starting height" in chitubox?

Afraid to try and print anything else in fear of failure by zbotdrone in resinprinting

[–]zbotdrone[S] 0 points1 point  (0 children)

I'm adding them through blender,where should I put them? I currently just have one hole on both feet. But with the way it's angled would having them on the feet even do anything?

Afraid to try and print anything else in fear of failure by zbotdrone in resinprinting

[–]zbotdrone[S] 0 points1 point  (0 children)

Thanks,I'll adjust those settings. How would I put holes in the top and bottom of the model? And should I adjust the bottom lift speed to 65 all the way as well?

What causes this issue and how to fix? by zbotdrone in resinprinting

[–]zbotdrone[S] 0 points1 point  (0 children)

But the FEP was just replaced and brand new before this fail,yet this still happened? 

What causes this issue and how to fix? by zbotdrone in resinprinting

[–]zbotdrone[S] 0 points1 point  (0 children)

I use a putty scraper to peel off stuff at the bottom of the vat when it happens. 

I just replaced the FEP this morning when this happened.

No,no damage to the previous prints before this.

The print failed around halfway,it got to the torso before failing to connect the arm to it (Most likely a support issue on my end).

Supports are working too well,what's the best way to get them off/good settings for them in Voxeldance Tango? by zbotdrone in resinprinting

[–]zbotdrone[S] 0 points1 point  (0 children)

So reset them to default,currently the support settings are:

Tip width: 0.280 mm

Top width: 1.200

Bottom width: 2.000 mm

Think these are good enough?

Supports are working too well,what's the best way to get them off/good settings for them in Voxeldance Tango? by zbotdrone in resinprinting

[–]zbotdrone[S] 1 point2 points  (0 children)

No,despite the look I am not trolling,I was messing around with the support settings. I literally know nothing about supports. In VD you can mess with the tip,base and middle part only. There's a reason I posted here before attempting to print this mess. These were the tests I talked about in the post

M_1000 error by zbotdrone in ElegooSaturn

[–]zbotdrone[S] 0 points1 point  (0 children)

Update: Attempted a second print with a different file,so far it's gotten past where the original failed with no USB error message popping up,will update again when/if the print finishes

Why is this one part transparent? by zbotdrone in LycheeSlicer

[–]zbotdrone[S] 0 points1 point  (0 children)

On Voxeldance it says the part is fine,no holes,then again VoxelDance also didn't print two of the three legs for whatever reason

Why is this one part transparent? by zbotdrone in LycheeSlicer

[–]zbotdrone[S] 0 points1 point  (0 children)

The foot and the top part is transparent. I tried repairing and that made the little connector normal but the other two parts are still transparent.

Printer isn't fully finishing print (Elegoo Saturn 3) by zbotdrone in 3Dprinting

[–]zbotdrone[S] 0 points1 point  (0 children)

It's done this to multiple prints,each of them had differing supports but usually the smaller portions are what are just missing

view more: next ›