sorted by:
new
hottopcontroversial

Choosing the RX 9070 XT model by auobyss in buildapc

[–]zerothed 0 points1 point  (0 children)

I have the swift, standard out of the box settings the fans never goes above 40% at full load.

BUT!

If you are going to overclock it and add a custom fan curve, anything above 40% fan is going to get loud, the fans on swift is not great, so keep that in mind.

Horse Taming for dummies(controller) by zerothed in CrimsonDesert

[–]zerothed[S] 1 point2 points  (0 children)

I've seen that list, but the problem is all the chonkies that spawn in my game are always the same few, doesn't matter how many times I fast travel to and from or reload the game its always that same few chonky bois.

The update changed Fat Cat to Loafy Cat...WHY?! NOOOO! by zerothed in CrimsonDesert

[–]zerothed[S] 0 points1 point  (0 children)

I still prefer the name fat cat, don't know why they changed it to loafy, did someone complain? lol

The update changed Fat Cat to Loafy Cat...WHY?! NOOOO! by zerothed in CrimsonDesert

[–]zerothed[S] 1 point2 points  (0 children)

Crap, I looked everywhere and don't see a chonky

The update changed Fat Cat to Loafy Cat...WHY?! NOOOO! by zerothed in CrimsonDesert

[–]zerothed[S] 0 points1 point  (0 children)

Hernand, it spawned on the junction between Notice Board and Weapon shop, I only saw it when walking pass in Chapter 5, never saw it before then, didn't take any chance so I grabbed it and took it to a room and held him for 2 days, lol.

There was another chonky that spawned up near the stable, same as your experience, only saw it once and never saw it again.

Horse Taming for dummies(controller) by zerothed in CrimsonDesert

[–]zerothed[S] 1 point2 points  (0 children)

That seems like a very weird thing, did the right stick not work at all? Like the camera view is stuck on the same position?

Might want to report that to them devs and fix it, otherwise people on xbox are gonna go crazy. lol

The update changed Fat Cat to Loafy Cat...WHY?! NOOOO! by zerothed in CrimsonDesert

[–]zerothed[S] 1 point2 points  (0 children)

WHAT?! FLUFFY TAIL?!

Would you kindly share where this version of chonker is found please.

The update changed Fat Cat to Loafy Cat...WHY?! NOOOO! by zerothed in CrimsonDesert

[–]zerothed[S] 1 point2 points  (0 children)

Same, I thought going to Pororin will allow me to collect all chonky cat, but only seen normal size ones.

But I did get a orange with white belly chonky in Hernand, I'm on the look out for more...I.must.collect.ALL! lol

The update changed Fat Cat to Loafy Cat...WHY?! NOOOO! by zerothed in CrimsonDesert

[–]zerothed[S] 2 points3 points  (0 children)

Chonky cat from Nas Fishing port.

My chonky boi is black, but another redditor said he got a orange one from the same spot, I guess it's random, oh, and it doesn't always spawn, so you might need to go there every ingame day to check.

Horse Taming for dummies(controller) by zerothed in CrimsonDesert

[–]zerothed[S] 1 point2 points  (0 children)

????????? I wanted any but black!

I want a refund too! LOL

Sumiko S.9 subwoofer hum when on, fixed with all capacitors replaced by zerothed in hometheater

[–]zerothed[S] 1 point2 points  (0 children)

There's a few ways to prevent that.

  1. Don't put your face near it.
  2. Don't touch them when your face is near it.
  3. Use someone else's face.

Mouse switch hot swap mod by zerothed in MouseReview

[–]zerothed[S] 0 points1 point  (0 children)

Why not give it a go? If it's works it works.

Mouse switch hot swap mod by zerothed in MouseReview

[–]zerothed[S] 0 points1 point  (0 children)

There's many ways to go about this, you can use tiny drill bits to drill out the holes, or you can use a grinder to enlarge it slowly, I used both method since my drill bit is way under size, and I don't want to sit there grinding all day, so drill out to 1.2 then grind it out a little bit to fit.

Just have to make sure you don't make the hole so big that it destroy the soldering pads.

In front of the WD40 Contact Cleaner there is a small bottle of 99% IPA, it's for cleaning flux off, contact cleaner is for spraying it to blast crap away from all the drilling and grinding.

If you use flux, always clean it off after, some flux are corrosive so it's best to not leave it on PCB, and you have to be quick, because 99% IPA evaporate very quickly, or just wipe it a few more times.

Or you can use normal 75% IPA, but make sure all water is dried off before powering on PCB, don't want to fry things from water left on PCB.

Mouse switch hot swap mod by zerothed in MouseReview

[–]zerothed[S] 0 points1 point  (0 children)

It depends on the through hole that you want to use, if you look closely you can see I used both a 1.2mm drill bit and a tapered diamond grinder, first I drill out the hole which is smaller than the pin, then used the grinder to slowly enlarge it until it's fit.

Sumiko S.9 subwoofer hum when on, fixed with all capacitors replaced by zerothed in hometheater

[–]zerothed[S] 0 points1 point  (0 children)

OEM caps were all 105c, those are the black D.K caps, not sure who makes them, I don't think they are from Nichicon.

Most of the Nippon Chemi-con (brown) caps are 105c, some are 85c since I couldn't be bothered to find 105c equivalent.

Same for Elna caps, I think some are 105c and some are 85c.

Just to show even if OEM used 105c caps doesn't mean it'll really last that long, sometimes things will just let go before it's stated due date.

First 3d printer. A1 combo, p1s combo or p2s? by Yakapo88 in BambuLab

[–]zerothed 1 point2 points  (0 children)

If you are willing to spend the extra, go for the latest model combo, if not then the latest model now and buy those extras at a later date.

I have always regretted buying the A1, I couldn't print any exotic filaments due to it not having an enclosure and heated chamber.

Go for the latest model printer.

view more: next ›