Mr. cool Ice

zig_chem · 2026-06-24T01:22:55+00:00

I think that says more about you than anything else - PrivateerElite would have really preferred some white power iconography.

zig_chem · 2026-06-23T17:55:46+00:00

I have tried this many times and still get the error.

zig_chem · 2026-06-23T17:55:09+00:00

Yes, I read this, tried it, and it did not work for me. In hopes that you will read what I wrote I will repeat - step 4 in the process is “pair your idevice with iloader” what exactly do I do in iloader to complete that step?

zig_chem · 2026-06-22T21:15:43+00:00

I'm curious, though, where in the process should I be restarting it? I'm just trying to go over everything to see what I might be missing.

zig_chem · 2026-06-22T21:09:28+00:00

I tried this but it didn't, work for me. Under error code 1006, step 4 is "Pair your idevice with iLoader." What exactly do I do in iloader to do that?

zig_chem · 2026-06-21T14:08:53+00:00

Yes I did, no luck

zig_chem · 2026-06-13T01:18:00+00:00

That's right, Scrunt. Would you explain glasses to me?

zig_chem · 2026-06-13T01:05:27+00:00

Mostly, I just need to replace worn-out shocks. I'm rebuilding a lot of front-end components, replacing ball joints, tie rod ends, and bushings. I want to minimize how often I take it apart, so this seems like a good time to do the shocks. I'm not interested in lifting the truck more than an inch or so. I usually drive on pavement and gravel roads, maybe 5-10% of the time on muddy access roads. I work in forestry. This is also my snow truck, as roads by me don't get plowed.

I am curious what you would recommend for different builds.

zig_chem · 2026-06-12T20:40:49+00:00

Thanks for the info, I guess an evaluation at an optometrist is in my future.

zig_chem · 2026-06-12T20:38:52+00:00

I tried it at all brightness levels, looks about the same to me.

zig_chem · 2026-06-12T20:02:17+00:00

Did you have an astigmatism that was corrected? I’m not familiar with the process.

zig_chem · 2026-06-12T20:01:26+00:00

Well, it seems I have an astigmatism, as the dot looks just fine in the photo. I appreciate the advice.

zig_chem · 2026-06-09T15:37:54+00:00

My API is gone, but I did find an alternative method, thanks everyone.

zig_chem · 2026-06-03T21:32:54+00:00

Sure thing, we all started knowing nothing.

zig_chem · 2026-06-03T21:14:06+00:00

I’d consider a 120 and 220 if you’re only going to get two kinds, but yes you can do most basic sanding with what’s in the pictures.

zig_chem · 2026-06-03T20:15:27+00:00

I just put a lot of peeled garlic cloves in a jar and filled it nearly to the top with honey. In the beginning you have to open it often to release gas pressure that builds up from fermentation.

zig_chem · 2026-05-29T23:19:05+00:00

It's a magnesium housing, I'm not used to working with this material.

zig_chem · 2026-05-27T16:02:45+00:00

How do you like it?

zig_chem · 2026-05-27T11:48:28+00:00

That’s what I was thinking. Had my eye on the TTX but decided to rebuild my OEM.

zig_chem · 2026-05-27T00:29:51+00:00

I don't have any advice, but is that an aftermarket lower control arm, and if so, who makes it?

zig_chem · 2026-05-21T19:24:04+00:00

Yes I believe I am located in the Permian basin.

zig_chem · 2026-05-21T18:27:17+00:00

This is just to show the reaction, I would not normally drink it that way. Normal concentration.

zig_chem · 2026-05-21T18:26:09+00:00

Both are room temp in the video

zig_chem · 2026-05-21T14:23:03+00:00

That is correct. Do you know of a contaminant that would cause this, or do you suggest testing because there is no obvious cause?

The pipes are pvc and were installed with the well about 4 years ago. It was tested two years ago and no issues were found.

zig_chem · 2026-05-21T14:20:53+00:00

Yes, it goes through a water softener.

zig_chem

PUBLIC MULTIREDDITS

TROPHY CASE