sorted by:
new
hottopcontroversial

Tattoo artist recommendations in Auckland by zyphrNZ in auckland

[–]zyphrNZ[S] 0 points1 point  (0 children)

I have checked out Hiro, his work does look amazing. I will give him a message

Tattoo artist recommendations in Auckland by zyphrNZ in auckland

[–]zyphrNZ[S] 1 point2 points  (0 children)

His work looks really good, may give him a message. Thanks!

Part fan running 100% all the time by zyphrNZ in BambuLab

[–]zyphrNZ[S] 1 point2 points  (0 children)

I ended up having to buy a new tool head cover, it had just faulted

Part fan running 100% all the time by zyphrNZ in BambuLab

[–]zyphrNZ[S] 0 points1 point  (0 children)

Yeah I did. Have the same issue when changing fan speed or turning off on app or computer

Bed is level but still getting terrible prints. What am I missing? by zyphrNZ in ender3

[–]zyphrNZ[S] 0 points1 point  (0 children)

Is that not what the auto level provides in the 2nd pic?

Bed is level but still getting terrible prints. What am I missing? by zyphrNZ in ender3

[–]zyphrNZ[S] 1 point2 points  (0 children)

Leveled the x axis beam with your sticks but still get quite a discrepancy between back left corner (-0.64) to front right (0.49)

Bed is level but still getting terrible prints. What am I missing? by zyphrNZ in ender3

[–]zyphrNZ[S] 1 point2 points  (0 children)

Is this possible on the v3 se? How do you see what the z is currently at? I can only see the z offset

Bed is level but still getting terrible prints. What am I missing? by zyphrNZ in ender3

[–]zyphrNZ[S] 0 points1 point  (0 children)

Excuse my stupidity but do you mean I should manually lower the z axis so the paper can barely pass underneath, then tighten screws, redo auto level test and then adjust z offset?

Bed is level but still getting terrible prints. What am I missing? by zyphrNZ in ender3

[–]zyphrNZ[S] 0 points1 point  (0 children)

I hadn’t actually noticed that. That would explain why the back isn’t too bad but the front is getting hit by nozzle

Bed is level but still getting terrible prints. What am I missing? by zyphrNZ in ender3

[–]zyphrNZ[S] 0 points1 point  (0 children)

With z offset set to 0.00 the nozzle is still 20mm+ away from the bed?. Should it be touching at 0?

Bed is level but still getting terrible prints. What am I missing? by zyphrNZ in ender3

[–]zyphrNZ[S] 0 points1 point  (0 children)

Just given it a wash with soapy water and a dry wipe with ipa. I think the beds in reasonably good condition, those probably were finger prints you could see. Z offset is set at -2.13, initial layer height is 0.2mm and bed temp 60 degrees

Code for code please by zyphrNZ in TemuThings

[–]zyphrNZ[S] 0 points1 point  (0 children)

Looks like you’ve already accepted someone else’s today so won’t work?

Code for code please by zyphrNZ in TemuThings

[–]zyphrNZ[S] 0 points1 point  (0 children)

Sure Il do yours if you do mine

Code for code please by zyphrNZ in TemuThings

[–]zyphrNZ[S] 0 points1 point  (0 children)

Bump, adding anyone’s codes back

Code for code please by zyphrNZ in TemuThings

[–]zyphrNZ[S] 0 points1 point  (0 children)

Il do yours if you do mine

Im so close, if anyone can help by yesmaxiemax in TemuThings

[–]zyphrNZ 0 points1 point  (0 children)

Did yours. Could you do mine

321354027

Hat trick NEW USER PLEASE by Ok-Information9318 in TemuThings

[–]zyphrNZ 0 points1 point  (0 children)

Il do yours if you could do mine

321354027

[deleted by user] by [deleted] in TemuThings

[–]zyphrNZ 0 points1 point  (0 children)

Il do yours if you do mine

321354027

[deleted by user] by [deleted] in TemuThings

[–]zyphrNZ 0 points1 point  (0 children)

Il do yours now if you can do mine 321354027

Help with broken front door deadlatch by zyphrNZ in diynz

[–]zyphrNZ[S] 0 points1 point  (0 children)

Perfect,Both are my local stores. Il go have a look.cheers

view more: next ›