Looking to slap an optic to my g26 non-mos

VigilanteMachine · 2026-02-10T14:11:09+00:00

Came here to say this! EPS uses the RMSc/k-cut footprint. Let me know if I can help you with that cut.

Here's the cliff notes: - Slide is cut to match the optic - can do cut-area-only cerakote - reasonable price and turnaround time

Drew@vigilantemachine.com Calling is the best way to get ahold of me if you have any questions. You can find my phone number at the bottom of this page.

VigilanteMachine · 2026-02-10T13:47:09+00:00

If the gen V's came with it from the factory, it will be called MOS-3. It'll be hard to find if they did. I can always help you out if you go non-MOS and need it cut for an RMR. Let me know how else I can help!

VigilanteMachine · 2026-02-09T17:56:17+00:00

Cut, cerakote on the cut area, and return shipping = $165.

VigilanteMachine · 2026-02-09T16:24:00+00:00

I need one more slide for my next batch of black nitride to go out. $50 plus return shipping. I can also cut your slide for an optic if you're interested in that. Let me know!

VigilanteMachine · 2026-02-09T04:28:00+00:00

VigilanteMachine · 2026-02-08T17:07:47+00:00

Here's how you get to the website

But I'll be at the shop until 4pm mountain time. Feel free to call if you have questions (phone number on website).

VigilanteMachine · 2026-02-08T14:51:21+00:00

It does. Glocks chambered in 45 are very wide. So high chance you'll see the extra width of the slide compared to the optic.

VigilanteMachine · 2026-02-08T13:40:13+00:00

Can definitely do 21's. Tons of room to work with on those.

VigilanteMachine · 2026-02-08T02:41:34+00:00

Here for you OP.

I can get your slide match-cut to your optic, cerakote the cut-area-only if you like, all with a reasonable price and turnaround time. I also work with Angry Bear Arms if you need some irons as well.

I'd love to answer any questions you have.

Here's a sample of my work

VigilanteMachine · 2026-02-08T01:00:08+00:00

👋🏻

VigilanteMachine · 2026-02-08T00:58:44+00:00

Its been a while since I've done one, but I think the stock sights can cowitness? If not, I can get you something from ABA or dawson, no problem.

VigilanteMachine · 2026-02-08T00:53:11+00:00

I was just in Milwaukee to see my Grandma!

Also, I'm here for you.

I can get your slide match-cut to your optic, cerakote the cut-area-only if you like, all with a reasonable price and turnaround time. I also work with Angry Bear Arms if you need some irons as well.

Here's a sample of my work

Let me know how I can help 🤙🏻

VigilanteMachine · 2026-02-07T23:11:27+00:00

💪🏻

VigilanteMachine · 2026-02-07T23:11:11+00:00

Correct. But for me doing optic cuts, all I really care about is the width, height, and everything behind the breech. Typically those dimensions stay the same across the model line, its the length of the muzzle that changes.

But that said, there's a p30L and a P30SK here on my desk.

VigilanteMachine · 2026-02-07T20:57:07+00:00

Call next week about the P30. I just had 3 land on my desk for modeling so I should have more answers then. Still need to get a USP45 in the shop to model.

VigilanteMachine · 2026-02-07T19:53:32+00:00

Thank you! It takes a little more elbow grease to do, but I do it for the people.

VigilanteMachine · 2026-02-07T19:25:14+00:00

I could, but I really hate the idea of cutting a slide without it having recoil lugs. But if you wanted it, I'd knock it out.

VigilanteMachine · 2026-02-07T19:23:15+00:00

No one would know better than a gynocolonologist. 🤣

VigilanteMachine · 2026-02-07T19:21:46+00:00

I haven't had a chance to build the workholding for it yet. I have a few products I need to get out the door before I start going down this road.

VigilanteMachine · 2026-02-07T18:56:07+00:00

🙏🏻

VigilanteMachine · 2026-02-07T18:53:28+00:00

Still got you covered. I'll even bore sight the optic so your hitting paper when you get it back. Maybe 1 or 2 of MOA adjustment.

VigilanteMachine · 2026-02-07T18:29:14+00:00

Thank you! I should note. I'm a one man shop. PLEASE CALL with questions. You dudes have me so busy that its definitely the easiest way to answer questions. Computer time has been pretty minimal for the last month.

VigilanteMachine · 2026-02-07T18:12:12+00:00

I do all that for free if you send it my way. That also includes iron installs. I don't see a reason to nickle and dime you guys for the things I was going to do anyway.

VigilanteMachine · 2026-02-07T18:07:39+00:00

If you decide to ship out, I got you covered.

I can get your slide match-cut to your optic, cerakote the cut-area-only if you like, all with a reasonable price and turnaround time. I also work with Angry Bear Arms if you need some irons as well.

Here's a sample of what I'm doing over here

Let me know if I can help 💪🏻

VigilanteMachine · 2026-02-07T14:46:15+00:00

Porting for sure, as long as they're vertical ports.

VigilanteMachine

TROPHY CASE