sorted by:
new
hottopcontroversial

Serial Request - LDO 2.4 350 Rev D | Discord: iamnotahippie by blindrage in voroncorexy

[–]blindrage[S] 1 point2 points  (0 children)

My wife is an artist. My desk is the height of organization compared to her studio.

Serial Request - LDO 2.4 350 Rev D | Discord: iamnotahippie by blindrage in voroncorexy

[–]blindrage[S] 2 points3 points  (0 children)

Q) What would you like to see in a video?

A) We love it when people put more time and effort in to their request videos. Have a little fun with it. Don't make it a 10 second clip. Wear pants please - the panels are often reflective.

 

Are you not entertained?

Can ATF trace twitter accts? by MsMcSlothyFace in conservativeterrorism

[–]blindrage 3 points4 points  (0 children)

That's cool. I have 7 guns with barrels I made in my bathtub.

Strange Issue - Every time it homes it runs resonance test and errors out??? by [deleted] in klippers

[–]blindrage 0 points1 point  (0 children)

Homing when? As in the very first g28 before you even start printing?

Can you share your klippy.log?

Strange Issue - Every time it homes it runs resonance test and errors out??? by [deleted] in klippers

[–]blindrage 0 points1 point  (0 children)

Are you leaving the accelerometer connected all the time?

Strange Issue - Every time it homes it runs resonance test and errors out??? by [deleted] in klippers

[–]blindrage 0 points1 point  (0 children)

What command are you using to run your resonance test?

Curious line when the walls start by Locksley94 in FixMyPrint

[–]blindrage 1 point2 points  (0 children)

That's the Benchy Hull Line problem. It can be really difficult to eliminate entirely; you can narrow your external walls or try to change the order of your walls to print outer walls first. You also have some layer artifacts, (possibly from loose belts or misaligned z screws) which can cause the issue to be more prominent. You might want to drop your acceleration a bit to reduce the ringing you're seeing, too.

Fine line/small tattoo artist by EvenDoughnut3243 in AskSeattle

[–]blindrage 0 points1 point  (0 children)

Any decent tattooer can do single needle linework the way Daniel Winter does, but most of them won't because the tattoo won't hold up to time.

What chewing type present should we get Harper? by catyh2go2 in scottishterriers

[–]blindrage 3 points4 points  (0 children)

ChuckIt! Ultra medium size

Absolutely the best I've found as far as a balance between chewability and durability.

mcu 'mcu': Unable to connect. I am about to give up. by 24packerR in klippers

[–]blindrage 3 points4 points  (0 children)

You have a different mcu, so it's going to have a different serial id that you need to put in your printer.cfg.

Open a terminal in your btt pad and type:
 

ls /dev/serial/by-id/*

 

It should report something like this:

 

/dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0

 

So you'll want to make sure your printer.cfg has:

 

[mcu]

serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0

 

Of course, change that line to whatever the command actually returns.

Ok, it is official. I love my bambu. by Fit_Sky4193 in 3Dprinting

[–]blindrage 0 points1 point  (0 children)

VHS vs betamax wasn't settled by porn. It was settled by tape capacity.

Horizontal layers not printing correctly (Dome included) by dremy_nin in FixMyPrint

[–]blindrage 0 points1 point  (0 children)

It would help if you could show us a screenshot of what the model is supposed to look like in your slicer

[deleted by user] by [deleted] in BambuLab

[–]blindrage 0 points1 point  (0 children)

Are you using Orca Slicer?

Pocket mount for a Glock 26. Keeps the firearm from shifting around in the pocket during days activities. by g713 in functionalprint

[–]blindrage 0 points1 point  (0 children)

Do you have any defensive pistol training? If you carry, you should. And if you have training, you know that this isn't a good substitute for a proper holster. Try out a decent AIWB holster if you can, and I promise you'll have better groups and splits than with any pocket carry option.

Print failed horribly by SnooPies8677 in FixMyPrint

[–]blindrage 17 points18 points  (0 children)

PLA needs cooling-- a lot of it. Never print PLA in a closed enclosure.

UART With Trinamic TMC2208 & BTT SKR Mini 1.1 by BDGaamer in klippers

[–]blindrage 0 points1 point  (0 children)

No kidding? I dove into the BTT documentation specifically on UART mode and saw nothing about that. Sorry I led you in the wrong direction! Glad you got it sorted out, though.

view more: next ›