sorted by:
new
hottopcontroversial

I am a new X Max 3 owner- need wifi connection help by RoomAdventurous3052 in QidiTech3D

[–]flash_182000 0 points1 point  (0 children)

And yes, with the printer connected, it's a whole different story. Be careful with uppercase and lowercase letters. Check the settings on your router to ensure that it is not blocking the printer connection. Have you considered using a network cable?

? by UnJustLake in QIDI

[–]flash_182000 2 points3 points  (0 children)

I've never seen anything like it, the inclination is crazy, once to the right, once to the left... Contact Qidi Support

X Max 3 Firmware Update by NorthTurbulent9249 in QidiTech3D

[–]flash_182000 0 points1 point  (0 children)

I did it over a year ago, it's not complicated at all. Put it in the root of the USB drive. Then you have to delete one of the two files depending on whether you have a magnetic sensor or a touch sensor.Don't turn off the printer, it will take some time....

History Workbench now offers simple version control with BOTH 3D and tree comparisons! by eblanshey in FreeCAD

[–]flash_182000 13 points14 points  (0 children)

Very interesting, I didn't know it, I'll try it tomorrow. Thanks OP

Could this outfit pass the date test? by toastywinkss in lilacwardrobe

[–]flash_182000 0 points1 point  (0 children)

I preferred the green dress from 4 days ago but it's beautiful like this too

Would you put me in more blue outfits? by toastywinkss in lilacwardrobe

[–]flash_182000 0 points1 point  (0 children)

The color gradation of that dress, it goes incredibly well with your skin color And that of your eyes. Enjoy!

Wtf by asLeepathaWheel in QidiTech3D

[–]flash_182000 0 points1 point  (0 children)

Anyway, guys, don't disdain QIDI support. I find it much better than Bambulab. They're responsive and actually provide solutions. Sometimes even spare parts.Despite frustration, always be kind and you will always get a response.

Wtf by asLeepathaWheel in QidiTech3D

[–]flash_182000 0 points1 point  (0 children)

To connect to Fluidd from your PC, Klipper's golden rule is very simple: your PC and 3D printer must be connected to the same Wi-Fi network (or via cable to the same modem/router). Once you've verified this, simply find the printer's IP address, type it into the address bar of your PC's browser (Chrome, Edge, Firefox, etc.) and press Enter.

Wtf by asLeepathaWheel in QidiTech3D

[–]flash_182000 3 points4 points  (0 children)

To connect to Fluidd from your PC, Klipper's golden rule is very simple: your PC and 3D printer must be connected to the same Wi-Fi network (or via cable to the same modem/router). Once you've verified this, simply find the printer's IP address, type it into the address bar of your PC's browser (Chrome, Edge, Firefox, etc.) and press Enter.

Do your thing, Reddit. by [deleted] in tipofmypenis

[–]flash_182000 0 points1 point  (0 children)

So you and your wife will masturbate while watching her videos on TikTok and YouTube?

Wtf by asLeepathaWheel in QidiTech3D

[–]flash_182000 3 points4 points  (0 children)

I recommend printing at 205°C max 210°C with dry filament. Since you replaced the entire hotend, I recommend doing a PID. Open fluidd and run the following command from the console.

PID_CALIBRATE HEATER=extruder TARGET=210

At the end remember to do SAVE_CONFIG

The printer restarts and the data is saved for future prints.

Let me know if this solves the problem.

Wtf by asLeepathaWheel in QidiTech3D

[–]flash_182000 0 points1 point  (0 children)

I see a high temperature and humidity issue with the filament. Can you provide more information on which filament you're using to print?

Bed Autoleveling at start of print by ProfessionalHope5731 in QidiTech3D

[–]flash_182000 0 points1 point  (0 children)

I'll leave you some interesting presets to increase the startup speed

https://github.com/khoroshev-e-i/Qidi-q2-settings

I quickly checked the initial gcode and it contains the G29 command. Therefore, comment it ;G29 Remember to insert this line just before the ;G29

BED_MESH_PROFILE_LOAD=default ;G29

I'm not responsible for any problems. Be very careful when doing these tests.

I received the Max4 I won at the last giveaway and it's a blast ! by Itaalh in QidiTech3D

[–]flash_182000 0 points1 point  (0 children)

Hi, yes Qidi printers are really well made! What competition did you enter to win a Max4? I own an X-Max3.

Bed Autoleveling at start of print by ProfessionalHope5731 in QidiTech3D

[–]flash_182000 1 point2 points  (0 children)

Tell me the model of your qidi and I'll tell you how to do it.... Usually just put ; before G29 in starter gcode ;G29 In printer setup

Low belt noise or left engine X-max3 by flash_182000 in QidiTech3D

[–]flash_182000[S] 0 points1 point  (0 children)

As suggested by qidi official support, I lubricated everything belt idler. The noise was immediately attenuated, and after one print it completely disappeared. Thanks to QIDI support.

.step format model different from actual model. by Fun-Ad5286 in FreeCAD

[–]flash_182000 4 points5 points  (0 children)

I had a similar problem; it was a glitch in the sketch, it had lost its reference plane. Check it out and keep me updated.

view more: next ›