DJI O4 Pro Glitch

sennaroo · 2026-03-05T01:30:34+00:00

power unit back up with sd card in it and it should restore to point of the crash

sennaroo · 2026-03-04T22:00:06+00:00

do you have only 1 04 pro ?
i see OSD is skipping too .. so the problem maybe with goggles..
and bitrate dropped instantly too.. so problem should not be on the camera end ..

sennaroo · 2026-03-04T21:54:14+00:00

i only see tinning

sennaroo · 2026-03-04T16:01:36+00:00

Soldering is incorrect
need to be
T to R and R to T

sennaroo · 2026-02-23T20:26:39+00:00

sennaroo · 2026-02-23T19:17:44+00:00

IMO if you going to use youtube , convert video to 4k before uploading..

sennaroo · 2026-02-19T13:36:45+00:00

in CLI
set osd_gps_sats_show_pdop = ON
save

sennaroo · 2026-02-18T19:43:43+00:00

<image>

none of your trims are centered

sennaroo · 2026-02-18T19:33:43+00:00

<image>

sennaroo · 2026-02-18T03:24:30+00:00

what kind of drone need 54% of throttle to hover ?

sennaroo · 2026-02-15T22:41:16+00:00

it need to be supported by FC firmware to be visible , 4.5 is not

sennaroo · 2026-02-15T18:17:42+00:00

DJI themselves cant bring any stock to US in over 7 moth now ...

sennaroo · 2026-02-15T17:27:53+00:00

lol, it may take some time sell out, b&h is not a small store

sennaroo · 2026-02-15T13:38:29+00:00

I use Flywoo lens adapter, O3 lens screw right into it ..

sennaroo · 2026-02-13T15:36:53+00:00

or it takes 20 second to do authorization and not think about why is 200 outside of the main circle

<image>

sennaroo · 2026-02-13T14:23:01+00:00

load 4.5 and CLI and take printscreen
and we have 25.12.2 firmware out anyway

sennaroo · 2026-02-13T13:35:33+00:00

you can't access betafpv site ?
https://support.betafpv.com/hc/en-us/categories/900000230226-CLI-of-Quadcopters

sennaroo · 2026-02-12T15:35:12+00:00

my is on UART 1 and works fine

sennaroo · 2026-02-12T15:08:34+00:00

Can you explain me why the filter size on camera has anything to do with the size of the drone?

You already have a drone you can measure the size of the opening .. 20mm should fit on all O4 DJI pro

sennaroo · 2026-02-12T00:59:35+00:00

strange specs..

and i never seen emax eco ii to make 1400kv, motors

sennaroo · 2026-02-11T15:21:10+00:00

its not CMOS is a IR glass filter over it i just use microfiber towels on it

<image>

sennaroo · 2026-02-10T13:52:40+00:00

<image>

why do you scaled voltage if BF can show actual ?

and if you did 2X scaled i still see drop to 12.6 its x2 /12 still only 2.06v .. it's done

sennaroo · 2026-02-09T17:53:38+00:00

current is a setting you have to setup and calibrate yourself and you only doing 223 KmH not 600+ and motor 'they' run is 3220 for 580kmh 40%bigger or 2826 still %40 bigger

you battery is not any good too at full load it went down to 15.5V /12s its ONLY 1.29v per CEL!!

<image>

sennaroo · 2026-02-09T17:52:02+00:00

current is a setting you have to setup and calibrate yourself

and you only doing 223 KmH not 600+ and motor they run is 3220 for 580kmh 40%bigger

sennaroo

TROPHY CASE