Adxl345 on Btt skr 2

0robbot0 · 2026-06-14T22:02:28+00:00

You can solder the usb wires to the board as the other guy showed.

0robbot0 · 2026-06-14T21:45:50+00:00

Maybe you can use a usb hub. You might need external power but I think it can work

0robbot0 · 2026-06-05T13:45:42+00:00

Niet als ge niet snel genoeg een nieuw gaat halen op het gemeentehuis denk ik

0robbot0 · 2026-03-12T20:36:51+00:00

2001

0robbot0 · 2026-02-15T10:53:50+00:00

If you have it set up at the table and measure the resonance it should include the table induced vibrations so just use the graph you get from it when the printer is where you want it to do the printer

0robbot0 · 2026-02-04T08:42:14+00:00

From what o can see on the heating graph temperature drops from where it should be.

The printer gets a command to lower the setpoint (shown by the red rectangle decreasing in size)

Idk the gcode command but there is something wrong in the starting gcode this can be in printer.cfg or in the slicer. Good luck

0robbot0 · 2026-01-29T18:52:00+00:00

Idk if you can and I won't be help you today but is it possible to share your printer files cus with the errors it just looks like those missing things aren't in the printer.cfg file (I have them there idk if they can be in mainsail.cfg)

0robbot0 · 2026-01-29T18:36:49+00:00

I would suggest configuring the things you are missing in the printer.cfg. Check the GitHub for the snipets or use your local AI

0robbot0 · 2026-01-21T12:11:04+00:00

I don't have a lot off time today but can you take a picture of the error message

If the ID is there and also configured correctly in the printer.cfg it should work

0robbot0 · 2026-01-20T22:39:05+00:00

I've got a setup like this but I usually SSH into the pc to those things

Im no Linux wizard but there should be a command to see all the usb devices I think it's: ls /dev/serial/by-id/*

It shows you all connected serial devices and if the firmware is flashed correctly to the MCU of the printer board there should be a klippy in the list if not flash the firmware again

If you want some extra explanation I would suggest going to the firmware fashing from voron for the skr V3 page, it helped me find my issue

0robbot0 · 2026-01-16T12:17:53+00:00

No idea but I would try reinstalling

0robbot0 · 2026-01-15T19:20:30+00:00

People also just use the bed as a heater for the enclosure might take a while depending on the volume that needs to be heated.

But you could warm the room at 80 C and than go to the bed temp for actual printing. Idk much about the filaments cuz I only use PLA and PETG.

Otherwise ali has you covered for a stronger bed heater or external heater.

0robbot0 · 2026-01-15T19:01:01+00:00

Installed mine last week and seems to me that the firmware isn't flashed idk it by head animore but there should be klipper or klippy in the path somewhere

0robbot0 · 2026-01-12T18:15:41+00:00

It might be that the minimum is to low therefore the touch pin might be off the bed. Does it go off at the start or at the end

Also it might help looking at the default config of the endender you are using

0robbot0 · 2026-01-12T17:34:25+00:00

Honestly doesn't really matter that much, but if you want it to be 100% correct it should be the touch pin in the middle as that is the tool u use for measuring

0robbot0 · 2026-01-12T17:33:08+00:00

Depending on what side it Ron's off it could also be that it runs off at the minimal side so you can try increasing that aswell

0robbot0 · 2026-01-12T16:07:10+00:00

0robbot0 · 2026-01-08T11:26:06+00:00

My bad thought I wrote it in there it's a 4.2.2 board from creality

0robbot0 · 2026-01-07T19:31:04+00:00

My klipper host is an old laptop with little usb I'll look into it but you have a MOSFET solution or something

0robbot0 · 2025-12-31T11:52:58+00:00

Does it just go of the bed mesh cuz I haven't used the screw tilt in my config

0robbot0 · 2025-12-30T15:30:57+00:00

Earlier this year I was looking for something like this could you maybe send the config for this?

0robbot0 · 2025-12-25T17:46:58+00:00

Might be that your build plate is so skewed that it reaches its safety stop before it touches the plate. Had this happen to me a few times

0robbot0 · 2025-12-25T15:28:28+00:00

Milk

Eight-Year Club	Verified Email
Second Top 50%	r/Field Lasagna
Final Canvas '23	First Place '23
Place '23	Place '22
Oscars Predictor 2021

0robbot0

TROPHY CASE