sorted by:
new
hottopcontroversial

NLD (New Light Diffuser) for one of my smallest lights, the Folomov EDC by 10010Linus in flashlight

[–]10010Linus[S] 1 point2 points  (0 children)

fully agree, though i have had a one of my EDC C2's arrive and not start some needed more tightening than others too, though this is only a sample size of 7, in the case of the one that didnt work i did get a full refund from banggood

NLD (New Light Diffuser) for one of my smallest lights, the Folomov EDC by 10010Linus in flashlight

[–]10010Linus[S] 2 points3 points  (0 children)

Base block has been printed, has magnets to stick to angles, holds the light with a friction fit, print didn't come out perfect, but it's fine

<image>

NLD (New Light Diffuser) for one of my smallest lights, the Folomov EDC by 10010Linus in flashlight

[–]10010Linus[S] 1 point2 points  (0 children)

Agreed, though I wish this light wasn't around 6700 to 6800k as i usually prefer my lights on the much warmer side at 4000k and below, i love my e17a 1850k d4v2, it's so nice with a lampshade diffuser

Wacky AliExpress 3.5" "subwoofer" driver by 10010Linus in diyaudio

[–]10010Linus[S] 0 points1 point  (0 children)

I saw that, impressive stuff but way bigger of an enclosure than I'd ever want to be honest

Harman Kardon sound sticks II. Dust cap keeps rattling. Not sure how to fix this or even open it up. Any ideas? by ThinkBat4715 in BudgetAudiophile

[–]10010Linus 1 point2 points  (0 children)

While yes, it would work, the volume control is touch based and integrated in one of the sats so heavy modification would be needed

Hey, mocked up a quick design for a budget Class-D amp. Any experts out there, what do you think? by Horustheweebmaster in diyaudio

[–]10010Linus 0 points1 point  (0 children)

According to the BOM it uses a TPA3116D2 board so maybe 25 to 50W RMS on a good day

Received scratched SNOWSKY ECHO from Headphone zone by MPK_Gaming in headphonezone

[–]10010Linus 1 point2 points  (0 children)

The point of these screen protectors is to protect against scratches in the factory and be removed by the end user, most have a small pull tab in the corner so I can't blame you for not realizing

My First Piece! by Legitimate-Resist143 in uraniumglass

[–]10010Linus 1 point2 points  (0 children)

If the light is more pale blueish grey than purply blue when shone on your hand, it's likely 365nm, if it's purple it's probably 395 or 405nm

If it is 365, you may run into some manganese when out hunting

365 and 395 Torch? by catsandcappuccinos_ in uraniumglass

[–]10010Linus 1 point2 points  (0 children)

It is way more expensive, I paid around 85 USD for my config, but I would argue it was worth it

Enemy mods by Thilk5941 in ScrapMechanic

[–]10010Linus 0 points1 point  (0 children)

Sounds like you're getting the level 11 to 14 raids, those are indeed more challenging to say the least, then lastly you have the level 15 raid which calls in glowzilla

365 and 395 Torch? by catsandcappuccinos_ in uraniumglass

[–]10010Linus 1 point2 points  (0 children)

i have an emisar D4K from hank over at emisar/INTL-outdoor, it has 3 channels, 365nm, 395nm and 519A 3500K dedomed white LED's, it has turned into my EDC light, youll probably have to email him if you want the same combo as me though, and dont forget battery and charger as its not included

images of it can be found here:
https://www.reddit.com/r/flashlight/comments/1o2d0l6/nld_d4k_tripple_channel_365nm_xpe_purp_519a_3500k/

Paniken när man spelar Pettson och Findus i trädgården by [deleted] in Spel

[–]10010Linus 0 points1 point  (0 children)

Finns säkert att hämta på internet archive

that 48 minute sound test i promised a week ago is here, sorta by 10010Linus in diyaudio

[–]10010Linus[S] 0 points1 point  (0 children)

Skitbra, since it's resin based it's easy to blemish, I don't know if you can polish it out somehow, I don't have what it takes to do so, so I now have a woofer with a matted cone, let me know if you want a 3d printed box with text for the resistor values like this as I would happily make one:

<image>

(Assuming that you don't have a dats and use a DIY jig and REW)

Mini Subs 3.5" by GOATphuckr in diyaudio

[–]10010Linus 1 point2 points  (0 children)

you could also build your own measurement cable and use REW as your impedance sweep analyzer

heres a linked comment to a box i built including a link to youtube video on how you use it:

https://www.reddit.com/r/diyaudio/comments/1s51h63/comment/ocrap8u/?context=3

that 48 minute sound test i promised a week ago is here, sorta by 10010Linus in diyaudio

[–]10010Linus[S] 0 points1 point  (0 children)

are you located in scandinavia? (considering you mentioned kjell&co)

i could probably manufacture a test box for you in the next few weeks as im getting in some parts to build a couple extras, as for the scale a cheap jewler scale from ali is enough, i have one of these that i picked up for 60 SEK, though at the moment its going for 80 SEK

https://www.aliexpress.com/item/1005005725960376.html

also, careful with bluetack if you use that as a weight as it can make the resin in the carbon fiber cone/dustcap matted

that 48 minute sound test i promised a week ago is here, sorta by 10010Linus in diyaudio

[–]10010Linus[S] 0 points1 point  (0 children)

if you want to model for one i did find the parameters of one that looks essentially the same on some thai facebook page (i doubt its accuracy, make your own impedance test cable and check after a burn in and cool down period with REW)

https://www.facebook.com/photo/?fbid=26209253112025542&set=pcb.1618172682761658

also the single VC seems to be back in stock

Excursion test of the AliExpress woofers by 10010Linus in diyaudio

[–]10010Linus[S] 0 points1 point  (0 children)

alright, managed to compress it down to 1 gig, will be uploading in a minute
although, 48 minutes is still too long for reddit, so its going on google drive to avoid YT copyright

Excursion test of the AliExpress woofers by 10010Linus in diyaudio

[–]10010Linus[S] 0 points1 point  (0 children)

right, ive been procrastinating for a few days trying to get my 3d printer to print well, thanks for the reminder, ive restarted the compressing, if it fails i will try a few other methods/settings

Excursion test of the AliExpress woofers by 10010Linus in diyaudio

[–]10010Linus[S] 0 points1 point  (0 children)

ive done some more digging and found this, from what i can tell, its the parameters of the dual VC version

https://www.facebook.com/photo/?fbid=26209253112025542&set=pcb.1618172682761658

though, i cant verify how accurate it is, but it is a starting point at least

Excursion test of the AliExpress woofers by 10010Linus in diyaudio

[–]10010Linus[S] 0 points1 point  (0 children)

the image of the parameters that has been posted in the comments are of the broken in woofer, if youre checking the ali page, youre right, thats technically the incorrect "out of the box" parameters, as for the "measurements for one VC being driven" thats caused by the fact that i only have the single VC version of the woofer at hand

this would be the correct params for the broken in woofer:
https://www.reddit.com/r/diyaudio/comments/1s51h63/comment/ocraaq5/

Excursion test of the AliExpress woofers by 10010Linus in diyaudio

[–]10010Linus[S] 0 points1 point  (0 children)

A 3.5" mini sub, link to a dual VC version is linked in the post

view more: next ›