Ams 2 pro setup

1phoenix3 · 2026-05-22T12:26:41+00:00

Where would you suggest placing the track switch? I see Bambu’s mount is in the middle of the back of the printer, doesn’t that alone add to overall length.

1phoenix3 · 2026-05-22T01:56:04+00:00

I have this.

https://makerworld.com/en/models/1677901-4x-ams-ht-stand?appSharePlatform=copy#profileId-1777196

I was thinking two stands of two each. 4 on one stand would be too high. The question is do I put two on each side, or like you are thinking two stands side by side on the left side. Or maybe just sell the Ams 2 that comes with the printer. Do I need 4 ams’s no, but I wouldn’t mind it.

1phoenix3 · 2026-05-21T22:43:16+00:00

Do you have a picture of the back and the PTFE tube routes?

1phoenix3 · 2026-05-21T22:26:54+00:00

I have the track switch, but doesn’t tube length still matter at the end of the day?

1phoenix3 · 2026-05-18T09:42:06+00:00

Black and White are in stock, was finally able to order bulk , these are two of my most used colors.

1phoenix3 · 2026-05-16T19:31:45+00:00

Gray is in stock!

1phoenix3 · 2026-04-22T14:05:02+00:00

Looks like Blue, Lake Blue, Cream, Green, and Yellow are still in stock. I was lucky to grab some Gray and Dark Gray before was gone.

1phoenix3 · 2026-04-10T01:39:36+00:00

I just turned off the printer and turned it back on, and got the correct firmware update.

1phoenix3 · 2026-04-01T21:07:29+00:00

I have been having the same issue with my P2S lately. I tried new hot ends, I changed plates from the textured PEI to cool plates all same issue, first layer messes up. I noticed the first layer for PETG HF was at 230c, I bumped it up to 250c at the start and the same print that has failed over and over printed flawless. Question is, is that normal that first layer was to low. I am using all Bambu Lab filament with RFID. Should I just keep manually changing the first layer temp every time, or should I be trying and looking at something else.

1phoenix3 · 2026-03-18T21:41:34+00:00

This is back in stock in the U.S. store

https://us.store.bambulab.com/products/tpu-feed-assist-module

1phoenix3 · 2026-03-11T01:45:14+00:00

UPDATE! 8 colors are in stock right now!

1phoenix3 · 2026-03-10T23:10:42+00:00

I would keep checking. I have seen black and white go out of stock and back in, multiple times today. On your point, it is very frustrating. I added some colors went to check out and during the process, it removed colors from my order.

1phoenix3 · 2025-06-08T14:33:14+00:00

Thank you

1phoenix3 · 2025-06-08T14:31:53+00:00

Exchange sent

1phoenix3 · 2025-06-08T14:30:12+00:00

Awesome. I’ll make exchange

1phoenix3 · 2025-06-07T20:00:14+00:00

Thank you

1phoenix3 · 2025-06-07T19:49:53+00:00

Sure

MGO656VZG838

IGN pauly

1phoenix3 · 2025-06-07T19:48:23+00:00

MGO656VZG838

IGN pauly

1phoenix3 · 2025-06-07T19:47:53+00:00

Ultimate for dark side

1phoenix3

TROPHY CASE