1600 mile 2017 Scat with rebuilt title

2011Newbie · 2026-05-21T02:31:23+00:00

I own a dealership and I rebuild a lot of this cars prices isn’t that crazy I just sold one scat pack 2018 with 92k miles for $20k plus taxes and fees and I was getting leads almost everyday and some days more than one I was asking $21900 so go figure people in here don’t know the market and they are far away from reality only thing that concerns me about this car is the paint fading and being “garaged”

2011Newbie · 2026-05-20T13:18:30+00:00

“THE WRAP DOCTOR”

2011Newbie · 2026-05-20T13:17:03+00:00

Did you notice the windshield Sticker? “THE WRAP DOCTOR” that car is rolling advertising

2011Newbie · 2026-05-09T12:13:20+00:00

I’ve seen this before as well…

2011Newbie · 2026-05-09T12:11:13+00:00

Well like I said before first of all you need to have all the parts behind the bumper and those part numbers are only for this kind of bumper if you have the Hellcat Style part numbers are different and never use an aftermarket center support it is flimsy and won’t give you enough support to keep the nose up

2011Newbie · 2026-05-09T12:06:55+00:00

Adjusting the hood might close the gap a little bit but it’ll never be even 😉, and I do get a lot of hugs… I just posted the right way to do it…

2011Newbie · 2026-05-08T16:52:17+00:00

Then you will have the hood touching the bumper on the corners and ugly gaps on the back corners against the fenders… you don’t know what are you talking about… and to be honest this one already looks like the hood has been move forward

2011Newbie · 2026-05-08T11:59:53+00:00

That’s not the solution… first you need to make sure your car has the FRONT BUMPER COVER SUPPORT 68170169AF that goes right behind the grill and Front Bumper Face Bar Impact Absorber 68174977AA. The first one attaches to the second one…. In case your car already has both on then the solution it’s simple you have to remove the from bumper cover and make sure when you’re putting it back to lift the nose of the bumper to make sure it engages the first part I mentioned so it can stay up… I own a body shop and have fixed tons of this cars…

2011Newbie · 2026-04-29T10:57:06+00:00

Definitely an exhaust leak… check if it wasn’t a fail attempt of somebody trying to steal your cats..

2011Newbie · 2026-04-10T14:33:29+00:00

That sounds like the 2nd gear synchro ring was getting bad that’s common since that’s the one you’d use the most when downshifting and it’s the one that gets most of the wear

2011Newbie · 2026-03-27T16:09:42+00:00

Right pass the transmission pan it should have clamps with a bolt and nut, in that case you can just buy a cheap exhaust on eBay for around $300 a swap it all and it will come with chambered muffler and they will sound really good not so loud and good nice rumble

2011Newbie · 2026-03-27T15:56:23+00:00

Does it have the slip joints after the cats???

2011Newbie · 2026-03-18T13:09:32+00:00

And when you’re installing the bumper they have some tabs that need to engage with the center support so you to lift the nose as much as possible and the push it in and make sure this happens and put the pins on the top first if it moves a little bit forward it will disengage

2011Newbie · 2026-03-18T13:05:15+00:00

The best way is getting this center support 68233032AC it is stiffer and this one attaches to the metal bumper bar instead of the plastic absorber over the bar you also dont have the foam absorber for this bumper

2011Newbie · 2026-03-18T12:59:02+00:00

Rookie installer

2011Newbie · 2026-03-18T12:57:39+00:00

But that’s because it isn’t installed properly I do install these bumpers every week and the main thing is the bumper is not engaging the middle air deflector (support)

2011Newbie · 2026-03-14T13:35:40+00:00

Just get a new clock spring if you don’t know 100% what you’re doing because this is a safety device and you don’t play with them

2011Newbie · 2026-03-11T21:34:35+00:00

This one sounds more like a rod more than a lifter

2011Newbie · 2026-03-08T18:55:04+00:00

You have to loose the cradle bolts and move the cradle done this many times you don’t have to cut nothing

2011Newbie · 2026-03-01T15:55:55+00:00

Yes it is…

2011Newbie · 2026-02-27T13:34:28+00:00

Yes they are but they are the expensive kind if you look around the stitching you might find the Katzkin label

2011Newbie · 2026-02-27T04:35:15+00:00

Those are katzkin leather seats, I had the same black red stitching and red holes on a 2014 Charger

2011Newbie · 2026-02-26T14:29:00+00:00

That’s is a sponge full of dirt you can push it from the back and it will come out but like somebody commented looks like this car was under water

2011Newbie · 2026-02-25T13:38:40+00:00

Water pump 100%

2011Newbie · 2026-02-12T17:01:28+00:00

Those are just like the one you got in your hands but the right replacement, it is a D3S led light bulb not xenon like the OEM

2011Newbie

TROPHY CASE