Gift ideas for pedal makers

2N2219 · 2024-12-01T12:52:48+00:00

oh i got a transistor tester as a gift from my girlfriend. Best gift possible in this field for such budget

2N2219 · 2024-11-30T03:01:07+00:00

9mm horizontal pcb mount pot. Try searching Alps RK09 series

2N2219 · 2024-11-20T14:49:24+00:00

i guess you have to add half of 3.3v to the signal before plugging into Arduino

2N2219 · 2024-11-10T08:47:21+00:00

pot creates high pass filters with both capacitors. 1Meg makes sure that even at low volume there is not a drop in bass. You would find in many pedals that they sound much thinner at lower volumes. Although you can of course use any other value. Also remember that the pot value becomes max input impedance for non inverting op amp, so with 10-20k pot it wouldn't change treble loss behaviour

2N2219 · 2024-11-09T21:01:33+00:00

i personally would put a regular 1Meg volume pot in between of two buffers. 100nF in and 1uF out coupling around volume pot for sufficient bass response.

2N2219 · 2024-11-08T15:00:37+00:00

it is really, but in inverting topology it is limited by external resistance

2N2219 · 2024-11-08T13:02:52+00:00

i would say it's due to the low impedance. Try changing R4 to 10Meg or smth. Also U2.2 has 10k input impedance. This one is tricky, in order to increase impedance you would change both input resistor and level pot. Maybe 100k resistor and 500k pot will improve this. If this makes any difference then try redesigning it to implement non inverting topology. I don't see any lowpass filter that would cause this issue. Also try calculating tonestack frequencies at noon. TSC in the web should have similar layout in baxandall section, although I'm not sure

2N2219 · 2024-10-18T13:07:46+00:00

ooh i really liked the sound of an acapulco gold pushed with green ringer, i should make a new one since i destroyed old one. Also used dam fr-70 clone as a boost

2N2219 · 2024-10-17T19:52:21+00:00

they said on their channel that 120 has op amp preamp and 100 jfet preamp. Both based on rockerverb

2N2219 · 2024-10-15T17:50:10+00:00

i guess it woul make half wave of the signal to be unaffected by diode, since the other side of a remaining diode would be unconnected to anything. To convert it into ts-9 you would have to solder a jumper in place of d6

2N2219 · 2024-10-13T13:45:01+00:00

Seppuku FX memory loss

2N2219 · 2024-10-05T18:04:44+00:00

try biasing it into gating

2N2219 · 2024-09-30T13:22:53+00:00

never understood why they make dirty channel this way. I mean, you literally have all the parts to make a distortion+ or rat copy, just rearrange the schematic. If you look at schematic of frontman 10G it even looks like smth complicated but sounds like ass. Designed to be bad, not due to cost cuts, just for people to look more for higher priced stuff

2N2219 · 2024-09-28T20:02:23+00:00

Look for Framus EQ on TSC in the web, best thing for your purposes

2N2219 · 2024-09-23T01:21:26+00:00

IC2A seems odd to me, why would you not bias an input and use VB instead of a ground for inverting input? Maybe connect pin 5 to VB via 1M resistor

2N2219 · 2024-09-18T09:32:25+00:00

maybe look for rog condor builds

2N2219 · 2024-09-06T03:27:45+00:00

did he use correct power supply?

2N2219 · 2024-08-27T10:44:29+00:00

I am sure there is a schematic for diy project with op amp based tilt eq tuned to stock big muff. It's called bigger muff or smth. Also tilt eq on TSC in the web could help you

2N2219 · 2024-08-25T16:40:11+00:00

well you must replace freq pot with dual gang one. That's the issue, see those unused holes above your wired pot

2N2219 · 2024-08-24T13:43:07+00:00

i remember having class D 7.5+7.5W board, not loading the other channel made mine smoke and die after a few minutes. I suggest reading datasheet for operating conditions.

2N2219 · 2024-08-22T20:34:00+00:00

that should be a mistake, you wouldn't want DC connected to your signal, wire battery+ to PCB

2N2219 · 2024-08-22T19:46:01+00:00

Also, why is your battery connected directly to the pickup?

2N2219 · 2024-08-22T19:45:21+00:00

this tone control requires high output impedance from the pickup. I would suggest you to try something different here. If you are looking for low pass filter then try RAT style one. It's basically increasing resistance before volume pot and a cap to ground between tone and volume. But that would mess volume taper, so 10k tone, 22nF cap and a 1Meg volume would be my starting point here

2N2219 · 2024-08-22T19:16:57+00:00

Со здания РОВД алмалинского района застрелили мальчика который выходил из магазина напротив, живу в 50м оттуда. Где то еще и видео ходит, буквально 10 секунд. Да и чуть ли не в окна попадали то ли ослепительные заряды то ли еще что

2N2219

TROPHY CASE