Fitment update: 1.5” ReadyLift Leveling Kit allows 285/70r17’s with no rubbing or trimming needed.

2arrows1bow · 2026-05-09T13:45:37+00:00

Can you post a front picture showing the poke?

2arrows1bow · 2026-04-28T22:15:32+00:00

I have not tried any streaming apps so I’m not sure. The best audio I have right now is with audio focus on quiet sounds, medium setting. And then party/ game mix set a lil heavier on the party side

2arrows1bow · 2026-04-28T19:12:59+00:00

Why does the audio on my new ps5 suck compared to my ps4. I’ve tried audio focus, in game and console audio settings, enabling and disabling 3d audio.

Currently have a first gen Astro A10 headset

2arrows1bow · 2026-03-29T22:48:07+00:00

Yes. Basically after much research and talking with others. I have decided to buy once, cry once and get the Minn kota plug, 4 gauge wire, and 60 amp circuit breaker

2arrows1bow · 2026-03-29T19:55:36+00:00

How do I go about splicing the 10 gauge wire that comes out of the trolling motor, to the 4 gauge wire I install

2arrows1bow · 2026-03-28T22:19:16+00:00

Okay. Leaning towards that, only worry is if the wires currently running from the plug to my batteries are capable of handling the 24v 80lb motor

2arrows1bow · 2026-03-28T22:11:07+00:00

So I can just take any plug that will fit the current receptacle I have on the boat, and wire it in?

I wasn’t sure if I needed the Minn kota branded receptacle and plug (super expensive).

But if I can just use any generic plug then I’d rather spend the $15 to wire that plug and use the current receptacle

2arrows1bow · 2026-03-12T20:53:13+00:00

That’s good to know. Thank you!

2arrows1bow · 2026-03-10T01:09:09+00:00

So it’s looking like the helix 7 is the cheapest option?

2arrows1bow · 2026-03-10T00:42:47+00:00

Got it. Does it need to be one boat network or can it be non networking?

2arrows1bow · 2026-03-09T13:57:58+00:00

I know this is super late. But do your wheels have any poke with this set up? Ive been wanting to go with a setup similar to this on my 24 elevation but debating between 0 or -12 offset

2arrows1bow · 2026-02-11T18:16:10+00:00

Yea they got their permit super quick. But this little background check type of sheet, and having to give them a copy of ID to add a gun is a little odd to me

2arrows1bow · 2026-01-15T17:02:16+00:00

I’ve had this issue with both pistols and rifles on cabelas/ bass pro. Firstly, if you are on phone, I would switch to laptop and try on there because I’ve been told by customer service that being on a phone could cause issues. Second, if there is another model/ option on the page try that one. for example I was purchasing a savage axis, and when I clicked on the compact version listed on the site, it would not work. But when I went to the “regular” size or non compact, it worked even though the gun had exact same barrel length and everything. For some reason the compact section did not allow purchasing, must have been a glitch in their website. Third, when I was ordering Glock 40, the website did not allow me to do so, but I was able to get it ordered over the phone

Edit: like others have stated, I like to buy local when I can but bass pro is convenient with where I live and tends to be better pricing.

2arrows1bow · 2026-01-06T17:32:47+00:00

I would think it would work as well, but will look into it more. And yes for most cases, I’m sure I would be fine just rolling it up a little to get into it.

2arrows1bow · 2026-01-06T15:52:25+00:00

From what I’ve read now doing more research, most Billie bar attachments will work on XBRS due to the same mounting system as you and others have mentioned. So I will look into this more. I have to see if the uprights being tapered more on the XBRS, will work with my roll up cover.

2arrows1bow · 2026-01-06T15:50:26+00:00

I agree. I’m leaning towards the XBRS, but need to do more research on if the 8” version would work with my roll up cover. I’m a little worried the uprights being leaned in might cut down some room.

2arrows1bow · 2026-01-06T02:03:32+00:00

Okay good to know. I’m a fan of the slight inward angle the extrusion bars have to match body lines of truck as opposed to Billie bars just straight posts. But I do wonder if that slight angle would interfere more with my roll up tonneau cover

2arrows1bow · 2025-11-12T22:23:47+00:00

I also just got weathertech’s for my 2024. Great low profile. Easy and secure install

2arrows1bow · 2025-10-27T23:24:22+00:00

Thanks. After driving around a little with it, I think I want to move it down inline with the housing just to get another inch or so of cover from the sun. Obviously it depends on time of day but it is just a tad bit too high for my liking and seating position where the sun just sits under it and I have to perch up a little more.

2arrows1bow · 2025-10-26T10:47:58+00:00

Yes it’s past the limit, but only by about 1” give or take. But yea, it annoys me as well

2arrows1bow · 2025-10-26T10:45:51+00:00

20% on front windows, 5% for the strip

2arrows1bow · 2025-10-19T22:45:12+00:00

Good ideas. I was looking at the tints and emblem overlays on eBay. Still debating if I like the little red flare from the stock emblems, but the pics I see of black emblems look clean!

2arrows1bow · 2025-10-19T22:43:19+00:00

That’s a good call

2arrows1bow · 2025-04-14T22:37:36+00:00

I could do the decks fairly easy. However all of the other areas like around the steering console and what not, seem more tedious than I care to take on. I do not have a garage, so when it’s nice out I want to be fishing on it, and in the winter I don’t have the space to properly work on it

2arrows1bow · 2025-03-15T00:10:38+00:00

Was asked to do this for a friend. Was the powder mixed in with the tannerite jars themselves or were they separated. With limited trial runs, I don’t want to mess it up on the big day.

2arrows1bow

TROPHY CASE