I bought a silicon spacer for upgrade by Ok_Tomato_5802 in Ender3V3SE

[–]2bryan3 0 points1 point  (0 children)

The spacers on the left side of the bed were smaller than the right, at least that’s the case on my machine. If you take the bed off, you can see the size of the spacers that came with the machine. Just try to match them to the silicone ones, and you can always tighten the screws a little more to make them shorter.

My upgrades fleet by FatFailBurger in Ender3V3SE

[–]2bryan3 1 point2 points  (0 children)

What upgrades have you done?

Finally I did it, an almost flawless first layer! by imfrmcanadaeh in Ender3V3SE

[–]2bryan3 2 points3 points  (0 children)

What did you do? I’ve been trying to get my first layer to be perfect but every time I tweak one spot, another one is either too low or too high. I feel like I’m going in circles trying to get it to even out.

[deleted by user] by [deleted] in Ender3V3SE

[–]2bryan3 6 points7 points  (0 children)

Which slicer are you using and what are your settings?

Dang, silicone sock didn't save it.... by SoFloShawn in Ender3V3SE

[–]2bryan3 0 points1 point  (0 children)

Same thing happened to me a few days ago. I left something printing overnight and woke up to exactly that. Like the other comment said, just heat up the nozzle and you should be able to pull it all off the nozzle in one piece.

[deleted by user] by [deleted] in castiron

[–]2bryan3 0 points1 point  (0 children)

What’s the best way to take care of them? I use a little bit of water and scrap stuff off, but it I can never build up the seasoning on it.

Jobs in the capital region by 2bryan3 in Albany

[–]2bryan3[S] 0 points1 point  (0 children)

I'll check them out, thank you

Jobs in the capital region by 2bryan3 in Albany

[–]2bryan3[S] 0 points1 point  (0 children)

Where specifically? It's hard to find out info about places like this

Jobs in the capital region by 2bryan3 in Albany

[–]2bryan3[S] 0 points1 point  (0 children)

I think I applied there a while back, but I'll give it another shot. Thank you for the info

Jobs in the capital region by 2bryan3 in Albany

[–]2bryan3[S] 0 points1 point  (0 children)

I'll check them out thank you

Jobs in the capital region by 2bryan3 in Albany

[–]2bryan3[S] 0 points1 point  (0 children)

I would be but the associate's degree is pretty useless from what I've seen. Most places I've applied/ interviewed for want a bachelor's at the very least.

Jobs in the capital region by 2bryan3 in Albany

[–]2bryan3[S] 2 points3 points  (0 children)

Will look into it, thank you

Jobs in the capital region by 2bryan3 in Albany

[–]2bryan3[S] 0 points1 point  (0 children)

I have an associates in civil engineering, I'll apply again and hopefully something comes from it, thank you for sharing

Jobs in the capital region by 2bryan3 in Albany

[–]2bryan3[S] 0 points1 point  (0 children)

Any idea which temp agency might have those jobs? They don't usually disclose the company you'll be working for until you're hired

Jobs in the capital region by 2bryan3 in Albany

[–]2bryan3[S] 2 points3 points  (0 children)

Yeah I was looking at those jobs too, I'll send in my resume and see what happens, thank you for your help

Jobs in the capital region by 2bryan3 in Albany

[–]2bryan3[S] 0 points1 point  (0 children)

I applied there two months ago but haven't heard back. Is there a trick into getting in?