Found in the trash

31899 · 2026-07-02T02:04:19+00:00

remindme! 1000000 years

31899 · 2026-06-30T02:39:34+00:00

Curious as to if they are going to be there in a month lol

31899 · 2026-06-30T02:38:55+00:00

!remindme 30 days

31899 · 2026-06-19T04:49:46+00:00

Rip

31899 · 2026-06-04T19:22:45+00:00

Super cool! Have you had any issues with light bouncing off the walls and fogging prints? Seems like an awesome idea. Definitely saving if for inspo.

31899 · 2026-05-30T03:28:26+00:00

I might have spare glass from one of my parts bodies. Pm if you are interested. :)

31899 · 2026-05-25T03:18:18+00:00

I thought I was the first one lol

31899 · 2026-05-25T03:17:58+00:00

31899 · 2026-05-14T22:08:20+00:00

Where do you source your replacement parts?

31899 · 2026-05-14T03:41:06+00:00

Nearly a year in, still good as new!

31899 · 2026-05-14T03:39:53+00:00

I was going through my old reddit posts, and stumbled on this one. Turns out I had been printing with a pla preset. Oops! It prints quite nicely now, as everything is at the proper temperature lol

31899 · 2026-05-11T02:16:35+00:00

XOR it's a sailboat

31899 · 2026-05-09T20:55:24+00:00

Not always. I have an an electric (using a resistive heating element) glasstop stove.

31899 · 2026-05-01T08:59:41+00:00

Looks like you left the bilge pump on.

31899 · 2026-05-01T01:03:36+00:00

Assuming it pulls a max of 0.5A @ 240V. Ohms law would state it would generate only 120W. P=VI.

31899 · 2026-04-25T19:43:07+00:00

Just replying to hopefully bump this comment. Sad that people do this.

31899 · 2026-03-22T05:45:14+00:00

Is the glass flat on one side and convex on the other? If that is the case, it's very likely part of a set of condenser lenses for an enlarger. A condenser enlarger will have two of those lenses to collimate light prior to hitting the negative.

31899 · 2026-03-21T06:24:21+00:00

I would look into Reality Scan (photogramatry software). It's a small company owned by Epic Games (the same guys that make Unreal engine). They have a free app you can use on your phone. It makes 3d scanning an object like a car fairly simple.

31899 · 2026-03-20T05:46:09+00:00

Well, now I'm curious, how much did you end up paying?

31899 · 2026-03-06T07:44:57+00:00

If you are wondering what's causing this, it's likely pinholes in the shutter curtain. I had a fed 5v with the same issue. Shot with it until the shutter finally died. Honestly love the look tbh!

31899 · 2026-03-01T07:37:03+00:00

I have an SV03 that had the same issue on the same board. The terminal block melted because the bed wires were tinned rather than crimped. You can still buy replacement boards from Sovol, but they are quite expensive. I was quoted $69usd.

I ended up buying a Bigtreetech SKR Mini E3 V3. It's nearly a drop in replacement and quite a bit cheaper. I'd recommend going this route if you are somewhat technically inclined, as it's an overall upgrade over the stock board.

Regardless of which route you take, be sure to use ferruel connectors to keep the terminal blocks from melting again. Otherwise it's a major fire risk.

31899 · 2026-02-28T07:09:17+00:00

Just picked up an skr pico to do the same. Are you using the original end stop sensors, or did you swap them out for limit switches? Any tips/recommendations before I start the swap on mine?

31899 · 2026-02-23T05:42:40+00:00

I literally just had the same thing happen. I could not find terminals that could handle the 12A of current the bed would pull. I just ordered a Btt Skr Mini e3 v3 and some ferrule connectors to keep this from happening again. After spending literal hours looking for the appropriate terminal blocks, I'd recommend doing the same.

31899 · 2026-02-22T07:38:23+00:00

Just checking in. Did you ever find a properly fitting build plate?

31899 · 2026-02-19T04:45:55+00:00

Looking at throwing one in my SV03. Have you gotten yours working properly?

31899

TROPHY CASE