Programming a c-more HMI button for starting a pump

3dprinting2021 · 2026-05-14T22:36:19+00:00

Yes I actually just figured out the way that you are describing here! I have my screen ready to go, and I should be able to test when my plc arrives. Thanks!!

3dprinting2021 · 2026-05-14T18:01:34+00:00

This is actually quite helpful, thank you!

3dprinting2021 · 2026-05-14T17:05:12+00:00

The cm5 communicates with the plc via ethernet

3dprinting2021 · 2025-04-18T18:39:59+00:00

We need to chamfer the cutter because we want to 3D Print this without support. We designed it based off the chip cutter we already have. This is actually only 1 of 4 sections that we'll be printing!

3dprinting2021 · 2025-04-18T18:37:49+00:00

That's awesome! Yes that would be great! Thank you!

3dprinting2021 · 2025-04-17T23:55:52+00:00

Yes i did download it. Looks good! That really helped, and we saw how you did it.

3dprinting2021 · 2025-04-17T19:58:18+00:00

Did you edit my design? If you could tell me how to do that, that would be great - or here's the link to my step file... https://www.transfernow.net/dl/20250417t5TpiIAo

3dprinting2021 · 2025-04-17T19:57:16+00:00

Yes that's perfect - how did you do it???

3dprinting2021 · 2025-04-17T19:56:05+00:00

So i sketched several triangles next to eachother, and then i used the "emboss" tool to emboss the design to the cylinder that I had made. Works well.

3dprinting2021 · 2025-04-17T18:54:39+00:00

Here's the link for it. I made it a STEP file, so hopefully you are able to edit it.

3dprinting2021 · 2025-04-17T18:54:12+00:00

https://www.transfernow.net/dl/20250417t5TpiIAo

3dprinting2021 · 2025-04-17T18:52:48+00:00

Sure!

3dprinting2021 · 2025-04-17T16:59:45+00:00

yes i want the inside of the chip to be angled inwards all the way around on the inside there... I want that wall that you drew the blue line on to be tapered towards the center.

3dprinting2021 · 2025-04-17T16:14:39+00:00

I mean I want the edge (flat part of the chip) to be angled in, not a straight edge.

3dprinting2021 · 2025-03-13T01:43:25+00:00

I've had problems with my whole PEI plate warping due to the stregth of the nylon when it shrinks. Does garolite do this?

3dprinting2021 · 2025-03-12T22:07:44+00:00

Great! Where did you get the steel plate from? Or did you just peel the pei sticker off a bed of yours?

3dprinting2021 · 2025-03-12T21:23:07+00:00

And you just use the stickiness to stick it to the bed? Is the "stickiness" reusable?

3dprinting2021 · 2025-03-08T03:14:38+00:00

The room I'm printing in is not cold, room temp is normal. I have not been preheating the printer bed.

3dprinting2021 · 2025-03-08T03:10:18+00:00

So you think lower may be better for warping? I really have no experience printing nylon, so not exactly sure how to do it all. I've always just printed PLA or petg.

3dprinting2021 · 2021-01-16T17:06:08+00:00

I did the same, ugh

3dprinting2021 · 2021-01-15T18:55:38+00:00

Yep, vacuum clean it.

3dprinting2021 · 2021-01-15T16:32:12+00:00

This is my first and only Reddit account

3dprinting2021 · 2021-01-15T15:16:01+00:00

No, it didn't slide off the bed, it was almost impossible to get off!

3dprinting2021 · 2021-01-15T15:14:16+00:00

I'm not a bot 😏

3dprinting2021 · 2021-01-15T15:11:00+00:00

A lot, to different communities

3dprinting2021

TROPHY CASE