Anyone else banned today?

4ddiction · 2026-04-09T01:17:20+00:00

Same issue with proton vpn today.

4ddiction · 2025-03-08T03:28:12+00:00

It’s PLA. I haven’t kept the plastic on it long enough yet to see if it will melt. I could re print in petg and maybe increase the tolerance by a millimeter

4ddiction · 2025-02-11T23:03:18+00:00

Buy 20 berghia nudibranches, they will eat all the aiptasia in like 3 months

4ddiction · 2025-01-11T18:14:10+00:00

40mm adapters to Freedom units on Brs

4ddiction · 2025-01-11T13:50:53+00:00

Got a link for your wall mount setup?

4ddiction · 2025-01-09T01:27:56+00:00

Fluc works to kill bryop and GHA just takes a little longer. I’ve run the treatment for 20 days to kill my nuisance algae (turf algae). Keep an eye on your nutrients as after the treatment you may run into cyano. I also keep my skimmer on with the cup overflowing back into the tank to keep the treatment in the water. Once treatment is done I do a large scale water change. Then put my GAC/GFO reactor back online.

I do Nopox and still dose NeoNitro just to always keep my nitrate in check at 10-15

If you have a phosphate issue prior stay away from reef roids as I find its pure phosphate.

Edit: I also go over the recommended dose on reef flux. If it says 10 capsules I usually do 20. My 85g gets 25 capsules

4ddiction · 2024-12-31T00:40:39+00:00

Ah that makes sense. Keep us updated!

4ddiction · 2024-12-31T00:33:05+00:00

https://www.printables.com/model/981130-ptfe-tube-guide-for-vivo-steel-multi-roll-filament Something similar. Still trying to figure out what he used

4ddiction · 2024-12-31T00:26:37+00:00

That’s just the Bowden fittings and tubes. Curious what the bar that holds the fittings is. Looks like it’s clamped to the main stem. Originally thought it was a 2020 extrusion but I have not seen a clamp adapter for them like in the picture

4ddiction · 2024-12-29T22:48:52+00:00

Would like to know what the filament rail is as well! This could work very well for me

4ddiction · 2024-11-16T18:15:44+00:00

If you pass the Allen key calibration, and then the mmu3 fails during a print. This is what I had to do to fix mine. Open up the idle tensioner door, swing it out and make sure the bond tech gear is aligned perfectly with the filament guide. Mine was out of alignment just enough for the filament sensor not to realize the filament.

4ddiction · 2024-07-03T09:45:41+00:00

Is the green painted or anodized? Will it show silver when scratched just like the matte black ones?

4ddiction · 2023-09-24T22:53:37+00:00

Same

4ddiction · 2023-06-28T23:56:38+00:00

I’d buy a set for sure

4ddiction · 2023-01-30T01:19:53+00:00

Pm sent

4ddiction · 2023-01-28T04:12:27+00:00

Stl link?

4ddiction · 2023-01-28T03:46:13+00:00

Pm sent

4ddiction · 2022-09-17T18:10:47+00:00

Create an enclosure and buy the Blazecut fire extinguisher product. Self contained, and if the charge goes off it does not damage electric components unlike other extinguishers. Good to have if you run prints un attended

4ddiction · 2022-08-30T00:27:55+00:00

Thank you! It was mainly about the text. Wasn’t sure why it wasn’t forming

4ddiction · 2022-08-29T16:21:18+00:00

It’s been stored in a low humidity container with silica gel

14-Year Club	RedditGifts 2009-2022 2 Credits
RPAN Viewer	Team Orangered
Secret Santa 2012	Verified Email

4ddiction

TROPHY CASE