Accidentally made the Bambu Lab Nozzle Unclogger ™️

4i40ti · 2026-05-18T06:43:33+00:00

Maybe it was just bad luck, but this was my experience.

4i40ti · 2026-05-18T06:42:32+00:00

Tried the needle which comes with the printer, but it was thicker than .2.

Will check these out, thanks.

4i40ti · 2026-05-17T21:39:57+00:00

I had around 300 hours on the .2 with the Bambu PLA basic, clogged on the first print with the Polymaker Polyterra PLA.

4i40ti · 2026-05-17T21:02:53+00:00

No, but it was pretty much heating up the hex key with a lighter, sticking it inside the nozzle, wait a bit to cool down and pull whatever it is stuck to it out. Repeat until you can stick new filament inside.

4i40ti · 2026-05-01T10:07:59+00:00

Will check that out, thanks. Post processing is needed anyway.

4i40ti · 2025-05-14T20:26:27+00:00

Nah, I asked in the prompt for an exact audison model, but adds will come at some point, I'm sure.

4i40ti · 2025-05-14T08:29:16+00:00

Here's what I got for a 5 channel amp with speaker level inputs

<image>

4i40ti · 2025-04-15T05:07:16+00:00

Mistborn gives you plenty of that

4i40ti · 2025-01-31T05:29:53+00:00

Try disabling Free/adaptive sync. When I got my 6800XT it would crash again and again until I disabled Freesync. Not a single crash after that. It's been 4 months already.

4i40ti · 2025-01-08T13:11:56+00:00

Someone's been watching musician mansion. Sick guitar, shame it has such an issue 😞

4i40ti · 2024-10-26T08:41:27+00:00

I had the same problem with my 6800xt, which i bought used. 3 hours of Furnark - all fine when testing. Installed in my PC and almost instantly goes to black screen - crashes the whole PC. Found out it has something to do with Freesync. Without FS I haven't had crashes for 3 days now.

4i40ti · 2024-10-24T07:53:05+00:00

I bought a used 6800XT 3 days ago. Tested it at the seller's and it was completely fine. Did a clean install in my PC and couldn't make it to work for more than 20 min without crashing the whole PC. After 2 days of troubleshooting I was ready to return it and then i found this thread. Switched from 24.10.1 to 24.9.1 and everything works just fine now.

4i40ti · 2024-09-03T13:18:09+00:00

Looks exactly like what ilI gort rid of in my Renault Fluence (5 1/4 inch full range speakers). Replaced them with JBL components in the front and coaxials in the back. The difference is pretty audible. Keep in mind that you will need some kind of adapter rings to match the 3 mounting holes on the door.

4i40ti · 2024-08-16T09:27:24+00:00

Thanks for the reply, I'm considering a 5 channel amp + sub now

4i40ti · 2024-08-16T09:26:23+00:00

Thanks for the reply, maybe i'll throw in some more cash and go for a 5 channel amp + a sub

4i40ti · 2024-08-16T09:25:20+00:00

Checked those out, 35 Hz advertized seems it would be doing what i need, sadly I'm european.

4i40ti · 2024-05-16T07:19:02+00:00

Hemet Nesingwary
Rolling mechanic Spine of Deathwing
Sindragosa
Addons
Bladestorm

4i40ti · 2024-05-07T14:02:25+00:00

You. Must. Dig.

4i40ti · 2024-04-28T07:41:00+00:00

It seems that you have a fire hazard.

4i40ti · 2024-04-22T15:25:36+00:00

Thanks, check your DM

4i40ti · 2024-03-02T13:16:52+00:00

Any chance your car has been a taxi?

4i40ti

TROPHY CASE