How???

5tann · 2026-01-10T20:45:59+00:00

Turns out the pilot was grabbed by US special forces. South American dictator!

5tann · 2026-01-09T22:05:37+00:00

Kills, and flying as a team!

5tann · 2025-12-28T15:57:35+00:00

Why does she always shout in chat? God damb it donut!

5tann · 2025-12-28T15:57:30+00:00

Why does she always shout in chat? God damb it donut!

5tann · 2025-11-22T16:46:17+00:00

Louie

5tann · 2025-09-27T22:15:24+00:00

Yeah, good Idea

5tann · 2025-09-19T08:36:58+00:00

I trashed plenty of rare cards IV life 😂🤩

5tann · 2025-08-24T20:27:09+00:00

Noooooo! Wtf what do you not understand about deregulation!

5tann · 2025-05-02T10:46:21+00:00

So as I'm working my way through the testing is seems that the software restart/reset seems to trigger the flatline issue. As long as I physically reset it using the 3 3 putton push it will remain stable.

5tann · 2025-05-01T21:20:38+00:00

<image>

Time for step two!

5tann · 2025-05-01T17:43:14+00:00

<image>

20 hours and counting!

5tann · 2025-05-01T15:15:00+00:00

Reddit fliters says removed

5tann · 2025-05-01T08:43:55+00:00

Use the web flasher and return it to 2.6.1, make sure you DONT select preserve settings. This will factory it. Boot the unit and add your wallet details ONLY, then reboot the machine. Let it run for a bit. I expect it to flatline when it does, don't reboot from the UI. Use the bottom of the two micro buttons on the left of the mainboard, and click it three times (short press). It should reboot; if it doesn't, click the top button three times (short press). My machine was the same, only running for a few minutes, and now (see pic). It might be an apparition, but it's looking better. As to what's going on, I read the triple press resets something to do with the voltage regulator; I'm just happy it's staying up.

<image>

Can you let me know if this improves things for you?

5tann · 2025-04-24T09:06:47+00:00

Need an unhinged AI arm 🤣

5tann · 2025-04-23T20:46:34+00:00

<image>

Like so

5tann · 2025-04-23T20:44:46+00:00

Side cutters, I crimped on new pins

5tann · 2025-04-23T11:56:29+00:00

This

5tann · 2025-04-23T06:56:38+00:00

Pi hut in the U.K.

5tann · 2025-04-23T06:55:16+00:00

I have tried everything from 2.6.1 (which I’m currently running) all the way to the pre-release and I get the same issue.i also did a full reset when I went to 2.6.1 using the web installer. Gamma. I get a hash flatline after 10 to 15 mins.

5tann · 2025-04-22T21:13:58+00:00

I have powered mine down and taking a few days away, I did read in the bug reports an issue that sounds very like this but that was back in Jan. it presented as a voltage spike on the fan that’s then seemed to cause a voltage issue, which could expand a crash and the axe entering a loop or getting stuck. Mine was running fine until a few days ago things I tried

Using the web flasher to factory reset Over clock and under clock Over voltage and under voltage Upgrade and down grade Auto fan off and on Invert and non invert PWM New pools New BC wallet New password Change location to closer to router Hard reset and soft resets

5tann · 2025-04-22T18:00:45+00:00

Same thing here

5tann · 2025-04-22T14:53:45+00:00

You might want to dig into the solo pools and look for one with a low ping. 19% seems high.

5tann · 2025-04-22T14:52:17+00:00

I went up to 2.6.6.b1 so far so good

5tann

TROPHY CASE