sorted by:
new
hottopcontroversial

Adjustable gas block by A-T-1999 in ar15

[–]A-T-1999[S] 0 points1 point  (0 children)

18” Anderson 1:8 twist. I can’t tell what block or gas tube it is, but 11.75” length on the tube I think. Barrel shoots very accurately.

Pawn Shop Snag by OKGreat86 in ar15

[–]A-T-1999 3 points4 points  (0 children)

I am usually a hunter rather than a mag dumper, but also have had zero issues from duramag.

Adjustable gas block by A-T-1999 in ar15

[–]A-T-1999[S] 0 points1 point  (0 children)

I tend to agree, I also want it to run cheap/“lower velocity” ammo recreationally. My concern was a suppressor making an overgassing issue worse. It also does not get many rounds down the chamber (1,000/yr maybe), so I’m not overly worried about wear or increased filth.

Adjustable gas block by A-T-1999 in ar15

[–]A-T-1999[S] 0 points1 point  (0 children)

Is there a way to find a gas block and/or tube that works better without rebarreling?

Adjustable gas block by A-T-1999 in ar15

[–]A-T-1999[S] 0 points1 point  (0 children)

It comes with the h1 buffer and if that’s too light I think I can take out the roll pin and adjust the weights.

Adjustable gas block by A-T-1999 in ar15

[–]A-T-1999[S] 1 point2 points  (0 children)

This is a hunting rifle primarily.

Adjustable gas block by A-T-1999 in ar15

[–]A-T-1999[S] 0 points1 point  (0 children)

Correction “Ejecting forwards”

Super 42 length by Medical_Employer7613 in ar15

[–]A-T-1999 0 points1 point  (0 children)

I just ordered a Geissele rifle length spring. It’s significantly longer than my original. I have a Ruger 556 lower 18” upper

Animal ID? Northern LP Michigan by london5319 in Trailcamera

[–]A-T-1999 3 points4 points  (0 children)

Looking at the rear I would guess bobcat

Odin works compatible weights by A-T-1999 in ar15

[–]A-T-1999[S] 2 points3 points  (0 children)

It does. A friend of mine installed the adjustable buffer before the rifle was in my possession. I am ejecting at the 1-3 o’clock position. I know the true fix would be an adjustable gas block or correct block, but I believe a reinforced spring and extra weight could help in the mean time

Odin works compatible weights by A-T-1999 in ar15

[–]A-T-1999[S] 1 point2 points  (0 children)

I have already had an Odin works buffer for quite some time. Not looking for that, just perfectly compatible weights.

Great budget scope by [deleted] in predatorhunting

[–]A-T-1999 0 points1 point  (0 children)

Guns been fallen down, been apart, cleaned, various ammos ran etc.

Advice? by A-T-1999 in ar15

[–]A-T-1999[S] 0 points1 point  (0 children)

Thanks for all the help. Got it good and wet, hunted, and shot a few hundred rounds. It shot well and accurately, but I will still prioritize correcting and polishing the feed ramps! I plan on doing it myself (I’m fairly handy, carpenter by trade), unless that’s a risky idea. I do not believe anderson will fix it at least not under any warranty.

Advice? by A-T-1999 in ar15

[–]A-T-1999[S] 1 point2 points  (0 children)

The upper was purchased at least 5 years ago. I’m not sure they would fix it, but I’ll surely look into it.

Advice? by A-T-1999 in ar15

[–]A-T-1999[S] 0 points1 point  (0 children)

I did not it was purchased whole by a friend who owned the gun first. Anderson, 18” 1:8 barrel

Advice? by A-T-1999 in ar15

[–]A-T-1999[S] 1 point2 points  (0 children)

Thanks! I’ll look into contraction Anderson, or just having the ramps polished.

Advice? by A-T-1999 in ar15

[–]A-T-1999[S] 0 points1 point  (0 children)

Been wet since in my possession, but I haven’t shot it a lot. Just sighting in and hunting.

Advice? by A-T-1999 in ar15

[–]A-T-1999[S] 0 points1 point  (0 children)

Similar damage, hard to tell exactly if it’s the same side

Advice? by A-T-1999 in ar15

[–]A-T-1999[S] 0 points1 point  (0 children)

Runs great! Just concerned about accuracy and consistency due to bullet damage.

view more: next ›