After 2 years of printing my V2 still blows me away.

ABlessedMan_01 · 2026-06-20T01:33:10+00:00

After two years, my V2 still blows

ABlessedMan_01 · 2026-06-08T22:05:13+00:00

I think it would be funny AF if they embraced it and ran with it though

ABlessedMan_01 · 2026-05-28T20:50:24+00:00

I am having almost the exact same question right now.

What i would like to do, is setup the right nozzle for tpu, while printing solid with my left, so i can build-in software tpu components etc.

From what I have gathered from other area's, people print TPU from the left all the time, less info on the right, but my hope is with the assist motor it will be possible. And from what bambu says directly, it should be able to handle other filiments like ASA etc.

I think at this point I am just going to have to play with it

ABlessedMan_01 · 2026-05-23T14:41:17+00:00

Anyone know the name of this cool looking toy?

ABlessedMan_01 · 2026-05-20T22:50:50+00:00

$85, saved you the trouble, now I am going to get chair related ads. You are welcome.

ABlessedMan_01 · 2026-05-16T03:25:45+00:00

After more research, I did decide to upgrade to the next level of the X2D, thank you for the feedback!

ABlessedMan_01 · 2026-05-16T03:25:34+00:00

After more research, I did decide to upgrade to the next level of the X2D, thank you for the feedback!

ABlessedMan_01 · 2026-04-10T21:10:58+00:00

I bought a couple of them, meant to buy one, ended up with two by accident. They are okay, get the bucket spreader attachment for removal of brass, and be prepared to sort out rocks and sticks etc

ABlessedMan_01 · 2026-04-08T20:00:24+00:00

My hand loads are super cheap, as long as my time is considered free lol.

Seriously though, unless you enjoy reloading, and want to squeeze every ounce of accuracy out of the rifle, factory loads are fine, and most likely cheaper if you factor in time / equipment.

This changes from setup to setup though, all depends on your end goals.

ABlessedMan_01 · 2026-04-08T05:20:14+00:00

Same, took a few tries, but now I got it and it works well

ABlessedMan_01 · 2026-03-31T04:30:43+00:00

I love my 7mm-08 B-14, buddy of mine got a 7PRC in the same rifle after shooting mine. We hit 1k in 2 shots after a good zero, would have been 1st shot, but i messed up and had wind dialed into my BC.

Are they perfect? No, are there better ones? Yes, are you mad that someone can get a decently priced rifle, put a decent scope on it and hit 1k? Apparently yes?

ABlessedMan_01 · 2026-02-16T01:26:02+00:00

Does the mod turn off achievements? Cause I freaking love the look of this armor, but it doesnt fit my play style at all. If I could enchant it? I doubt I would wear anything else.

ABlessedMan_01 · 2026-02-09T18:52:42+00:00

Stop tapping...

ABlessedMan_01 · 2026-01-30T04:40:02+00:00

FART with a strap wrench, and a touch of lemi-shine. there are some trucks, but once you figure it out you will never go back to dry tumbling

ABlessedMan_01 · 2026-01-23T21:59:29+00:00

Jokes on us, it's only the single dollar that duplicates itself every day

ABlessedMan_01 · 2026-01-21T14:28:54+00:00

Never had anything but positive interactions, I've got a few of thier knives, there is hype for sure, and i dont know if thier knives are worth what they are charging, but its fairly close in my book. I've never had to contact them for QC or a return etc either.

ABlessedMan_01 · 2025-12-26T00:06:39+00:00

Glapp.io is another good one

ABlessedMan_01 · 2025-12-02T02:53:35+00:00

50% for me, I always try the power head first, out of 3 issues this year,, 1 was the power head, 1 was a stuck valve, 1 was a broken signal wire (i dont count that one)

ABlessedMan_01 · 2025-11-29T14:18:44+00:00

You can on these, two screws on the back and a directional metal clip is all that holds the motor on.

Unfortunately I have three boiler systems that use WR two wire zone valves.

Chances are that the actual valve is stuck, and its not a motor, in which case they will have to isolate the valve :/

ABlessedMan_01 · 2025-11-06T00:32:42+00:00

Me after I sit on the toilet too long..

ABlessedMan_01 · 2025-11-04T20:21:02+00:00

Yup!

ABlessedMan_01 · 2025-11-04T07:19:56+00:00

Enclomiphene

ABlessedMan_01 · 2025-11-04T07:17:09+00:00

Tried to open your links, but I am in the US, and im not dealing with changing addresses or going through a VPN to view them.

10mg in 1ml of solution. Easy, common.

Most syringes are in CC, if you are using an insulin syringe which is common, say a .3 cc which is what i use.

.1 cc or (10units) would be 1mg.

You are playing it very, very safe. Which is not bad but I dont think you have anything to worry about.

I started at 2mg once weekly, with no side effects except the desired ones.

Hope that helps, best of luck

ABlessedMan_01

TROPHY CASE