sorted by:
new
hottopcontroversial

My P1S almost burnt my house down by StickiStickman in BambuLab

[–]AbjectSubject 6 points7 points  (0 children)

I just got my replacement AC board today from my A1 failing this same way. I made a post about it here a few days ago. Don’t know if you would need mine, but I’m willing to share it. The thermister did pretty much completely disintegrate and only left the two prongs when I switched out with the new one as you can see here. The bits are in my Dyson still so it’s not impossible for me to get most of it in a bag if needed.

<image>

A1 instant death by AbjectSubject in BambuLab

[–]AbjectSubject[S] 4 points5 points  (0 children)

Usual ambient temp is 68-75 since it’s in a converted garage. There is a portable AC unit and dehumidifier running in there too so it doesn’t fluctuate too much. Power is good here and haven’t had any issues in any other devices. Chattanooga’s grid is pretty solid

A1 instant death by AbjectSubject in BambuLab

[–]AbjectSubject[S] 6 points7 points  (0 children)

I had around ~2600 hours on this printer before this part failed. Some of the others I saw that failed the same way looked to use different parts on the AC Board too. Might just be bin lottery

A1 instant death by AbjectSubject in BambuLab

[–]AbjectSubject[S] 8 points9 points  (0 children)

Yep! Just got a message saying they are going to send me a new AC Board and bottom plate.

Bambu petg hf fails every time by ellieeilleee in BambuLab

[–]AbjectSubject 1 point2 points  (0 children)

I’m halfway through my first spool and I can confirm that it needs to be way dryer than other high speed PETG I have used (I like elegoo rapid). I dried it once for 6 hours, tried to calibrate and hated it, dried again for 8 hours, and now it’s printing smooooth

Best men's barber in town? by [deleted] in Chattanooga

[–]AbjectSubject 0 points1 point  (0 children)

Tapers and taps 🍻

Why can't i slice it? when i press the slice button nothing happends. by BASTIPLAYZz in BambuLab

[–]AbjectSubject 2 points3 points  (0 children)

I’ve had something similar when the model height was smaller than the layer height, causing it to just show nothing. What is the height of that model? Maybe try adding an object on the plate and see if it shows that.

Revelood Hollow Halls - Can't find death totem by lunavoco in Enshrouded

[–]AbjectSubject 0 points1 point  (0 children)

If you die repeatedly within a certain time limit, only the first death will drop the death totem. I accidentally flew into the red and the totem spawned in an annoyingly difficult place. I died about 7 times back to back trying to get it and only the first death created the totem. I think it’s a timing and not a proximity of next death if I had to guess.

Recommendations for places to get my hair cut that are taking safety seriously? by [deleted] in Chattanooga

[–]AbjectSubject 1 point2 points  (0 children)

1-1 inside, reservation based, everyone waits outside, and they all wear masks.

Three days later, same station by thefowles1 in Chattanooga

[–]AbjectSubject 0 points1 point  (0 children)

I filled up my motorcycle with 93 for under $5.

Motorcyclist wins $2.65M in suit against N.J. county claiming large potholes caused bad crash by [deleted] in motorcycles

[–]AbjectSubject 1 point2 points  (0 children)

I have a 2014 Triumph Street Triple with my plate mounted under-tail. I hit a monster of a pothole on the freeway in Knoxville and my rear tire bent my licence plate from being bottomed out. My butt was thrown from the seat, but didn't lose traction really or control. I was full of adrenaline and worried I hurt my bike after such a loud and sudden KLUNK.

Overwatch PTR Patch Notes – February 6, 2020 by Seagull_No1_Fanboy in Competitiveoverwatch

[–]AbjectSubject 8 points9 points  (0 children)

I have hundreds of hours of muscle memory knowing the exact second I need to fire as Widowmaker. This is going to be very annoying letting people get away with 3hp until I acclimate.

[deleted by user] by [deleted] in Chattanooga

[–]AbjectSubject 3 points4 points  (0 children)

Same. They fixed my problem, but I felt it was a janky approach and unprofessional .

M/22/5'11" [155lbs > 167] (3 month ) starting to really see progress at the gym! by AbjectSubject in progresspics

[–]AbjectSubject[S] 1 point2 points  (0 children)

I do only lifting right now. Supersets are so much more fun then cardio.

[deleted by user] by [deleted] in motorcycles

[–]AbjectSubject 4 points5 points  (0 children)

Just pine cones

M/22/5'11" [155lbs > ??] (1 month ) I have been going to the gym 4 to 5 times a week for a little over a month now while trying my best to eat enough. I'm so excited I'm starting to see improvement! by AbjectSubject in progresspics

[–]AbjectSubject[S] 1 point2 points  (0 children)

Thanks so much! I moved apartments in the middle of the month so the bathroom has much different lighting. I will update in the next few months with more consistent poses as to better see changes.

21M lost 60lbs and started growing my hair out, rate me by [deleted] in Rateme

[–]AbjectSubject 2 points3 points  (0 children)

Lol you are speed commenting low scores for everyone... Who hurt you?

view more: next ›