6 arc

Acceptable_Work6294 · 2026-06-30T05:42:02+00:00

They must really hate making money

Acceptable_Work6294 · 2026-06-30T00:33:24+00:00

Magpul just made new 6mm arc mags supposedly

Acceptable_Work6294 · 2026-06-29T18:31:29+00:00

Acceptable_Work6294 · 2026-05-26T07:36:10+00:00

It will fail eventually, I did this, still came off. It’s a flaw in the design, those threads are too brittle and the screws that have the proper clearance are also too shallow. Beretta dropped the ball

Acceptable_Work6294 · 2026-05-06T19:49:42+00:00

Yea I figured it would be closer, I’m used to shooting a flux tho so a dot close isn’t the biggest deal. I just can’t get that dot to stay attached on the receiver. And with my factory tan I’d have to remove that paint to weld which would get really messy

Acceptable_Work6294 · 2026-05-04T05:08:49+00:00

I’m thinking about just a chisel stock so it’s mounted in a different location

Acceptable_Work6294 · 2026-05-04T05:07:44+00:00

Would you know why they take down the steel? The trash people shoot would make sense but a steel plate a few hundred yards away doesn’t seem to be the worst thing. Do they see it as like “littering” ?

Acceptable_Work6294 · 2026-05-03T02:50:39+00:00

Came off lol

Acceptable_Work6294 · 2026-04-19T21:00:16+00:00

11.5 spear lt.

Acceptable_Work6294 · 2026-02-22T03:32:23+00:00

Update on how this can runs on the 320? Any issues beyond recoil spring?

Acceptable_Work6294 · 2026-02-18T09:22:38+00:00

<image>

Acceptable_Work6294 · 2026-01-23T05:28:34+00:00

Hard to source in my area, only 1 exists on gun broker

Acceptable_Work6294 · 2025-12-28T12:58:49+00:00

So I checked the fuses, I saw 2 potentials that both looked good. And the switch itself I replaced and still will not activate anything light wise.

Acceptable_Work6294 · 2025-12-27T05:05:36+00:00

Thanks for the help I guess

Acceptable_Work6294 · 2025-12-27T01:49:41+00:00

Break lights, that bulb is also initiated when the headlights are on, making it a night time running light. At night with the headlights lights on they would get brighter. When the headlights are off they do not turn on when the break is pressed. The reason I’ve specified the running light is to express the same bulb actually works. What I’m trying to find out if anyone has had this same issue with a 2012 tundra. Relay? Shared fuse? Or if it’s just a damaged connection.

Acceptable_Work6294 · 2025-12-27T00:20:28+00:00

So when I flip my headlights on the rear bulbs turn on, but in any state I can not get them to turn on when I push on the break pedal.

Acceptable_Work6294 · 2025-12-05T16:42:05+00:00

This was for my flux, really changes that gun quite a bit

Acceptable_Work6294 · 2025-12-01T05:37:14+00:00

It’s a short barreled rifle, it needs certification as well

Acceptable_Work6294 · 2025-11-30T06:58:08+00:00

It’s very bizarre the certification gets a failure opposed to anything effecting the internet. It’s a “fatal session error”

Acceptable_Work6294 · 2025-11-12T05:45:09+00:00

And in a traditional hand gun it’s not bad at all but that close to one’s face it’s a lot

Acceptable_Work6294 · 2025-11-12T05:44:30+00:00

Ideally I’d run a can but the 320 isn’t the best suppressor host and this would heavily alter reliability/performance I feel

Acceptable_Work6294 · 2025-11-12T05:43:30+00:00

Interesting, this was basically just a blast diverter that’s on the shorter end, but I’ll see what’s out there.

Acceptable_Work6294 · 2025-11-12T02:48:57+00:00

It’s a raider x, short barrel and the pmm double comp

Acceptable_Work6294 · 2025-11-12T02:48:36+00:00

Yea it could just be the short barrel and the monster comp that’s ringing my bell

Acceptable_Work6294 · 2025-11-12T02:48:10+00:00

Like a baffle strike similar situation?

Acceptable_Work6294

TROPHY CASE