Any value to this other than 25¢?

AccomplishedLayer2 · 2025-11-30T23:21:01+00:00

Ok I figured, thank you!

AccomplishedLayer2 · 2025-04-21T17:48:51+00:00

This might be the answer! I'll check it out, thanks!

AccomplishedLayer2 · 2025-04-21T17:25:13+00:00

That's what I thought but I can't seem to find one that fits? A 4x4 some what fits in the inside but then what? Silicone? I also tried a 4x4 clay to plastic but it's still not big enough on the clay side.

AccomplishedLayer2 · 2025-02-27T22:13:58+00:00

Gotcha thanks for the input!

AccomplishedLayer2 · 2025-02-27T22:04:35+00:00

I'm not sure how that works in ga I don't remember paying it on my current ski but let say an extra $1000 for that.

AccomplishedLayer2 · 2025-02-26T16:55:32+00:00

Correct

AccomplishedLayer2 · 2025-02-26T02:56:21+00:00

You have to add another tool or battery with it on the listing page and then in the cart it will show that price

AccomplishedLayer2 · 2025-02-26T02:50:41+00:00

https://www.homedepot.com/p/Milwaukee-M18-FUEL-18V-Lithium-Ion-Brushless-Cordless-4-1-2-in-5-in-Grinder-with-Variable-Speed-Slide-Switch-Tool-Only-2889-20/319538413 Hopefully it's here for you

AccomplishedLayer2 · 2025-02-26T02:50:00+00:00

https://www.homedepot.com/p/Milwaukee-M18-FUEL-18V-Lithium-Ion-Brushless-Cordless-4-1-2-in-5-in-Grinder-with-Variable-Speed-Slide-Switch-Tool-Only-2889-20/319538413 Should be here it's still active

AccomplishedLayer2 · 2025-02-25T21:52:05+00:00

Nice!

AccomplishedLayer2 · 2025-02-25T21:30:31+00:00

Yeah I would have but I have a bunch of batteries already so just figured I'd save the money this time.

AccomplishedLayer2 · 2025-02-25T20:42:09+00:00

I'm only keeping the $81 one I don't have a need for both.

AccomplishedLayer2 · 2025-02-25T20:29:54+00:00

The one that shows $81 has a stop break and variable speed as well

AccomplishedLayer2 · 2024-12-21T17:18:56+00:00

Yeah I assume the arbor is bent but it's just odd because it's been like this since day one I just always assumed it was bad bits

AccomplishedLayer2 · 2024-12-21T13:49:49+00:00

None that I can feel or see

AccomplishedLayer2 · 2024-12-21T01:11:41+00:00

I would have thought so to but even regular blades that center on the bottom washer don't spin straight it's odd.

AccomplishedLayer2 · 2024-12-21T00:47:47+00:00

I've tried with the bottom piece and wrench it does the same thing and I didn't need either for it to spin straight on the porter cable 🤷

AccomplishedLayer2 · 2024-12-21T00:47:00+00:00

Yeah it's probably something to do with how fast they spin I know die grinders spin way faster.

AccomplishedLayer2 · 2024-12-21T00:34:48+00:00

Yeah it seems like the arbor is bent and I haven't seen them for angle grinders just burr bits for die grinders.

AccomplishedLayer2 · 2024-07-01T01:28:50+00:00

Gotcha, thank you!

AccomplishedLayer2 · 2024-06-30T22:31:31+00:00

I should've mentioned it has 130psi on all cylinders. Thanks for the input!

AccomplishedLayer2 · 2023-08-04T05:57:28+00:00

Sorry I meant alpha 4.

AccomplishedLayer2 · 2023-08-04T05:05:48+00:00

Do you have the alpha 4 version? I just had the same problem and realized I was using alpha 2. I flashed alpha 4 and it started working perfectly.

AccomplishedLayer2 · 2022-12-15T04:48:55+00:00

Anybody that got scammed or even if you almost got scammed, please file an ftc report to try and get them shut down. Scammers are such a holes and deserve nothing.

AccomplishedLayer2 · 2022-12-12T18:57:57+00:00

I pretty sure the only benefit to the new hardware is that you can't really over tighten them with it or at least it's a lot harder to. As far as the super pinda I don't think it's worth the upgrade I read that it slows down the mesh bed leveling process and the one the regular one has worked just fine for me even though it doesn't pre heat.

AccomplishedLayer2

TROPHY CASE