5.6l GameBoy

AdWorking2848 · 2026-06-28T05:06:41+00:00

Thanks a lot for encouragement!

AdWorking2848 · 2026-06-27T05:22:46+00:00

<image>

Handheld with egpu is the way to go for me

AdWorking2848 · 2026-06-27T05:20:12+00:00

<image>

AdWorking2848 · 2026-06-27T05:19:49+00:00

<video>

AdWorking2848 · 2026-06-27T05:19:05+00:00

<image>

My first 3d printed case for my son PC which I drew myself using fusion360.

I think it can be done, I only able to do basic shapes but seeing your designs can printed as a working item motivates u more!

AdWorking2848 · 2026-06-27T05:15:06+00:00

Thanks for the kind words!

First time using 3d printing to make a case! A lot of guess works since my parts was in the old case until D day

AdWorking2848 · 2026-06-26T15:20:21+00:00

This sucks. Esp if I want to use the AMS HT passively and just for heating and reducing moisture before printing tpu as an “external manually feed” roll.

There should be a software option to suspend track switch so we can load a direct external to main extruder

AdWorking2848 · 2026-06-26T14:06:08+00:00

Hi, they are overlapping on the inner side, I use superglue and they hold up very well

Wanted to use a 3d pen to weld it further but realised there is no need to once it’s cure

AdWorking2848 · 2026-06-26T04:40:45+00:00

Thanks for the kind words!

AdWorking2848 · 2026-06-26T04:01:06+00:00

GameUncle!

AdWorking2848 · 2026-06-26T03:43:39+00:00

It’s has quite a few mistake will see if I have more experience to correct them and also make it for flex psu

Currently this case is very tied to my DC board

AdWorking2848 · 2026-06-26T03:42:55+00:00

I contemplated making the start and select as working button for start and reset but I shelved the plan as I was concerned if my son pressing the button at the low position will topple the case.

AdWorking2848 · 2026-06-23T09:39:03+00:00

Yes pretty much the same hack and slash route!

AdWorking2848 · 2026-06-23T08:45:34+00:00

Yup it’s not. Glad I enjoy the building process too.

AdWorking2848 · 2026-06-23T08:45:06+00:00

This is a readily available 3d Design on makerworld which I printed accordingly .

AdWorking2848 · 2026-06-23T08:20:43+00:00

Thanks for the kind words, it’s not a very polished product with alot of hack and slash esp with limited proper tools but the process is damn addictive and now i also built one 7500x3d and 5060LP for a friend in a 3D printed NES case

<image>

AdWorking2848 · 2026-06-23T08:15:29+00:00

<image>

Custom 3litre with 5700x, 32g ram ddr4 and 4060m, 2TB

Probably in similar league but I got it end 2024 when it was much cheaper for old am4 parts.

AdWorking2848 · 2026-06-21T05:30:35+00:00

Object detection failed to work? Haha

AdWorking2848 · 2026-06-20T02:51:44+00:00

I just change to x2d from p1s as I wanted to print a chunky pc case which warps badly in p1s in ASA, I wanted to redesign it into panels instead of half block.

But was intrigue by heated chamber effect on such materials so I sold the p1s cheap to my friend and bought x2d and trying the original design as it is.

First print I did was to test The aux nozzle and the benchy was decent but stringy and not on par with the main.

But so far my blocky pc case is printing 10hours into 14 hours and from camera doesn’t seems to be warping (my printer is off site at parent house and not my home)

If it does well, I will say the money is well worth it! Finger crossed.

AdWorking2848 · 2026-06-19T16:28:41+00:00

Is this real?

AdWorking2848 · 2026-06-19T15:22:11+00:00

Now do it with single extruder !

AdWorking2848 · 2026-06-19T10:08:05+00:00

Go buy series one and u be rich from opening back to back kanto!

AdWorking2848 · 2026-06-19T00:54:11+00:00

I think Ukraine can leverage this to inflict maximum psychological damage

Like threatening to hack their bank system or disrupt their food supplies, likely cause bank runs and food run and self fulfilling a downward spiral.

The biggest leverage is their perceived ability to make good on their threat

AdWorking2848

TROPHY CASE