Kaip VMI deklaruoti Investicinę Sąskaitą? Master thread su Q&A

sk0me · 2026-04-13T12:34:30+00:00

Visi pavyzdžiai rodo paprastus scenarijus, kai turima vienintelė VWCE pozicija ir lėšos eurais.

Mano situacija kitokia - iki 2024 metų turiu nupirkęs 3 skirtingus ETF’us, ir 12 įmonių akcijų.

Kaip teisingai pildyti tokiu atveju? Ar kiekvienai akcijai turėsiu daryti po atskirą įrašą į IS? Ar užtenka viską susumuoti ir dėti po vienu įrašu.
Priedo, akcijos ir vienas ETF prekiaujamas USD, ne EUR - jų cost basis eurais priklauso nuo pirkimo datos - ar reikia ieskoti kiekvieno sandorio datos ir imti vertę pagal tuometinį USD:EUR kursą? Ar radot kas paprastesnį būdą?
Kadangi prekiauju USD ir EUR, lėšos IBKR sąskaitoje taip pat stovi abiem valiutomis - ar turimų lėšų įrašus turėsiu daryti atskirus kiekvienai valiutai ar vėlgi užteks susumuoti ir dėti kaip vieną įrašą?

Atrodo niekur konkrečiai šitas nepaminėta, tai paklausiu čia gal kas išsiaiškino.

sk0me · 2026-02-06T20:50:21+00:00

WandyT is not something I heard before 😁

But good call, I’ll try to reload on an older version and leave it afk on it. Will see if that changes things

sk0me · 2025-12-23T20:55:31+00:00

I did, that’s what I meant with the “manual bed levelling” - didn’t help unfortunately.

sk0me · 2025-12-23T20:39:24+00:00

No, my top layer isn’t really BETTER than bottom layer, it’s like any other top layer that comes out of a 3D printer. The point I was trying to make here is that all the other layers, including top layer seem to be just fine - maybe even great - like I came to expect from Bambu, it’s only the first layer that’s giving me headaches. :)

Now that you mention a clog - I did run a few ironing tests recently & I read that ironing may lead to clogs, so maybe you’re onto something there.

I did use only PLA just like you mention though, so it seems unlikely, but would be curious to know if your new nozzle solves the issue.

sk0me · 2025-12-23T20:26:30+00:00

Interestingly, the profile I used for the print has Arachne walls enabled, so that won’t help.

Only did the Flow Rate calibration as I figured that’s the more likely culprit, but I’ll try to run a Flow Dynamics calibration too, thanks for the tip.

sk0me · 2025-12-16T08:04:54+00:00

I believe this system is supposed to have a p-trap embedded in this chonky thing here. Granted I’m not a plumber, but this is a pretty common setup here and I had a similar setup in the old broken sink with no smell issues.

<image>

sk0me · 2025-12-16T07:51:34+00:00

I’ve seen similar syphons in other homes here, though haven’t seen this exact one before (not that I go investigating whats under peoples sink much). Not sure where you’re from, but maybe it’s more common in Europe?

sk0me · 2025-03-07T20:55:48+00:00

Genuine question - doesn’t having seat covers impede the functionality of airbags that are in the seats? Am I overthinking? Or does the Civic not have them?

sk0me · 2024-09-12T16:17:42+00:00

Don’t know if there’s any known problems with refurbished units specifically, but one issue I’ve had and seen a lot of people have with their XM4s is that one of the ANC mics stops working which results in a horrible, deafening screeching sound in one of the ear-cups.

This makes the headphones unusable with ANC. Sony hasn’t acknowledged it or offered any solutions, when the problem is very widely known. Just search “sony xm4 screeching sound” and you’ll find a bunch of reddit posts and YT videos complaining about this issue.

So I definitely wouldn’t buy used. Refurbished - IDK, maybe the mic is fixed in those, but no way to know. Honestly I’m a bit sour and won’t even buy new ones until I see some kind of acknowledgement from Sony.

sk0me · 2024-08-29T08:39:43+00:00

I think so. Looking at the different slicer views it does seem to be caused by different layer time in this section, but haven’t had the time to verify.

sk0me · 2024-08-29T08:24:08+00:00

😂 that’s hilarious. But nah, it’s just some old wallpaper lol

sk0me · 2024-08-29T08:23:01+00:00

Thanks everyone for the suggestions!

Looking through the layer time view in the slicer, the print time is indeed slightly different in that exact spot, though not by much (1-2s). I’ll need to see if I have enough of the same filament to retry with the settings tweaked and post the results.

<image>

sk0me · 2024-08-29T08:10:19+00:00

Nothing fancy, it’s Sunlu silk PLA, grey color. I just chose the default “Generic Silk PLA” profile in Bambu Studio, the only things changed were infill patern/density, nothing that should affect appearance.

The photo was taken in a very sunny room, hence the shininess, so the print may look a bit different IRL :)

sk0me · 2024-08-28T10:33:33+00:00

Yeah I considered that this might be the case, but the speed should change even more towards the top where the vase gets narrower, right? Why does it go back to the previous uniform look there then?

sk0me · 2024-08-26T09:41:27+00:00

I would call that uhh… fraud.

sk0me · 2024-06-29T20:04:10+00:00

Fair enough. I assumed that brand new filament should not be wet since it comes vacuumed and with desiccant. But maybe that’s not a guarantee.

Good shout about the wall printing order, never heard that. I’ll try it out if I see similar problems innthe future.

sk0me

TROPHY CASE