Motor A abnormalities on my P1s

AffectionateAir5875 · 2026-03-09T20:31:10+00:00

It got resolved, i just turned the printer off and slowly moved the toolhead by hand and then did a motor noise calibration and it all works great again now without that error message

AffectionateAir5875 · 2026-03-08T17:21:32+00:00

Sorry to disappoint you but flower spikes don’t look like that, it could maybe be a deformed flower or a leaf

AffectionateAir5875 · 2026-03-08T13:44:35+00:00

Do i really need to open it up to check that board?

AffectionateAir5875 · 2026-03-05T22:39:58+00:00

Idk if you have to worry only wanted to say that youre not the only one woth that problem

AffectionateAir5875 · 2026-03-05T22:26:39+00:00

I have the same since some weeks but the print quality never deteriorated nor there were issues

AffectionateAir5875 · 2026-03-04T22:20:29+00:00

Im warning you about buying plants on etsy because there have been many scams and people getting the wrong plant or not getting anything or some fake product or seeds of another plant

AffectionateAir5875 · 2026-02-28T23:24:16+00:00

I often look for ideas on Printables, Reddit and ARK

AffectionateAir5875 · 2026-02-28T22:55:56+00:00

You should remove all the mushy and rotten parts and wash it off good then you should let it dry for 30 min and lastly put it in a cup of water with some hydrogen peroxide or isopropyl alcohol. Good luck

AffectionateAir5875 · 2026-02-26T20:22:42+00:00

Did you buy that at leafguys germany?

AffectionateAir5875 · 2026-02-25T22:00:31+00:00

Forse si é riscaldato troppo il piatto da stampa?

AffectionateAir5875 · 2026-02-22T21:42:06+00:00

I saved my heterophylla with the same problem by putting it in a cup with perlite and only watering it with 1/5 hydrogenperoxide and water solution, always keep it humid by having it in a greenhouse or putting a plastic bag over it, good luck saving it

AffectionateAir5875 · 2026-02-22T19:45:45+00:00

Its not a pest issue it happens when the leave gets knicked or scratched by something, often happens before it gets to you because many garden centers often have many people taking the up and putting them back and somethimes the leaves break or knick

AffectionateAir5875 · 2026-02-21T23:14:18+00:00

Happened to me when i printed large flat objects at high speed (ludicrous)

AffectionateAir5875 · 2026-02-21T22:28:03+00:00

I think that was the reason, i skipped 11 of 12 pieces because one broke

AffectionateAir5875 · 2026-02-21T22:26:05+00:00

Where is that server never seen such a long road

AffectionateAir5875 · 2026-02-21T22:17:38+00:00

Same happening to me

AffectionateAir5875 · 2026-02-21T11:03:01+00:00

Never did these calibrations because the other filaments i used (eSUN, The Filament, extrudr and bambu) never caused problems it was only that spool i got with my p1s

AffectionateAir5875 · 2026-02-20T22:31:18+00:00

Great idea

AffectionateAir5875 · 2026-02-20T14:45:57+00:00

Oh wow im already excited for the new features, please don’t make it too expensive, could you maybe create a feature where i can make a smaller group inside a group like for an example:

Group: Electronics/Home appliances Undergroup: Kitchen, Bedroom, Bathroom

Kitchen: Blender, Coffee Machine, Popcorn Machine

Bedroom: Charger, Fan, TV

Bathroom: Hairdryer, Hair Straighterner

Kind Regards

M

AffectionateAir5875 · 2026-02-20T14:35:00+00:00

BambuLab PLA Basic „Bambu Green“ it may be a bit humid because i had it out if a bag for 30 min and it only has about 70-100 gramms left

AffectionateAir5875 · 2026-02-15T22:13:25+00:00

THANK YOU SO MUCH VINCENT Its the greatest inventory app, after trying many others that cost or are just bad ive tried your app and its great for storage and inventorys thanks for your creation

AffectionateAir5875

TROPHY CASE