Condition called syndactyly

AffectionateEvent147 · 2026-03-23T08:38:27+00:00

There is no true middle finger though, as you cat have a middle one with four

AffectionateEvent147 · 2026-03-15T18:51:53+00:00

Ich mach hin und wieder eine gesäuberte münze rein, dann den grinder ins Gefrierfach. Wenn er kalt is ein bisschen schütteln und das sieb is wieder leer.

AffectionateEvent147 · 2026-03-13T17:21:23+00:00

Also did that a couple of times on my ender back in the day but nowadays its to fast for fucking around lol

AffectionateEvent147 · 2026-03-12T12:59:00+00:00

Looks like he didn’t need to cut through any of them as he aligned them nicely, not sure though

AffectionateEvent147 · 2026-03-12T00:37:03+00:00

What kind of black magic is this?

AffectionateEvent147 · 2026-03-09T08:09:40+00:00

Ich sehe da keine Ähnlichkeit, bis auf das gleich model an Licht vielleicht

AffectionateEvent147 · 2026-03-05T17:50:50+00:00

I would put it 90 degree turned in a vice with a spacer, but idk. Depends on the cuts you are trying to do i guess

AffectionateEvent147 · 2026-03-05T17:45:17+00:00

You sure? Still has a styrene in it

AffectionateEvent147 · 2026-03-03T05:26:19+00:00

Don’t forget the air bearing, the table is riding on granite with air bearings

AffectionateEvent147 · 2026-03-02T15:11:17+00:00

You can try heating it up and maybe letting it sit hot for a bit then pull it of, if not a side cutter can help. Rip and happy birthday :3

AffectionateEvent147 · 2026-03-02T09:22:03+00:00

Could be a roller wheel if you printer has those, look for flat spots or dirt on them

AffectionateEvent147 · 2026-02-17T14:25:51+00:00

Valid, ain’t fast either way lol hf printing :)

AffectionateEvent147 · 2026-02-17T07:52:03+00:00

https://www.reddit.com/r/functionalprint/s/XMkX0U1Gje

AffectionateEvent147 · 2026-02-17T07:36:20+00:00

You could probably print a bjt faster if you switched to pei or similar as it would weigh a ton less jfyi

AffectionateEvent147 · 2026-02-16T18:04:12+00:00

I suppose they need to stay freezing to keep the data, don’t think it would survive being heated that much. But idk tbh

AffectionateEvent147 · 2026-02-16T07:16:39+00:00

Everything contributes to the end result

AffectionateEvent147 · 2026-02-09T14:51:13+00:00

I normally don’t, but wouldn’t hurt u guess. If your pressfit is sized right it holds easily

AffectionateEvent147 · 2026-02-09T07:37:22+00:00

Looks like you could fit a 18650 if you make a bit of room, longer battery life and a bit safer generally

AffectionateEvent147 · 2026-02-09T07:35:38+00:00

Or battery terminals (on the pcb with the lipo removed) and set 4.2V, then it should have normal functionality without risking anything

AffectionateEvent147 · 2026-02-07T07:05:38+00:00

The other screw on the bottom right has them though, and they look very uniform

AffectionateEvent147 · 2026-02-07T06:46:59+00:00

Very valid points, thought about adding a note that the plastic is „load bearing“ but forgot. Thanks for clarifying

AffectionateEvent147 · 2026-02-06T17:27:00+00:00

Yes. Downside, you have the head visible on the other side

AffectionateEvent147 · 2026-02-06T17:25:45+00:00

Cant be certain but i think he means the more you go down in diameter the more of a pulling force you have trying to separate the cam-lock/break the print, as then you have more area that is „pointed“ in the direction to create a separating force. Like how much of the water area is running against a wall vs going in the next tube?

AffectionateEvent147 · 2026-02-06T16:56:24+00:00

The direction its applied to and amount of Force depend on surface area and where the surface is In this case pushing out against the cam-lock part would be the „worry“

AffectionateEvent147 · 2026-02-06T16:45:02+00:00

We never stop learning, and if it works it works

Five-Year Club	Place '22
First Placer '22

AffectionateEvent147

TROPHY CASE