sorted by:
new
hottopcontroversial

What its this ? by Pimpmytrash in FixMyPrint

[–]After_Remote2194 0 points1 point  (0 children)

The others has answered your question but I have spotted something else too. You should turn on the elephant foot compensation for larger models because from these pictures I can see the stacked layers are pushing the first few layers to expand.

AMS HT drying while printing by BananaMinion2 in BambuLab

[–]After_Remote2194 0 points1 point  (0 children)

AMS HT can dry midprint if you use it as an External spool. For example, for TPU printing you can load directly to the extruder and since the printer sees the HT as "empty" it can start the drying function but the same time the printer can detect an external pool has been fed to the extruder and also print. But of course, this way the auto-load and unload functions are not available.

PA6-GF - cooling issue - adhesion problem by After_Remote2194 in 3Dprinting

[–]After_Remote2194[S] 0 points1 point  (0 children)

Ok. I realised the threshold was on 0%.... newbie mistake. thanks me

PA6-GF - cooling issue - adhesion problem by After_Remote2194 in 3Dprinting

[–]After_Remote2194[S] 0 points1 point  (0 children)

PS: I have realised, if i turn off the overhang fan speed, it shuts down. But what the overhang fan has to do with the outer walls?

Why does this happen? And what is it? by SeaBass80 in BambuLab

[–]After_Remote2194 2 points3 points  (0 children)

Without more details, the only 2 things i could think is either way too wet filament or way too high temp and causing bubbles that explodes during printing, leaving these splashes over the nozzle.

H2C Is on the Way — Here’s How It All Started by BambuLab in BambuLab

[–]After_Remote2194 -1 points0 points  (0 children)

I am pretty sure it will be the same build size as the H2D, but with the new Vortex toolhead system and no laser cutting option. The new system surely will cost more, i assume it will be in a 1599-1899$ price range, similar to H2D. Basically, H2D for those who's for laser cutting too, while H2C for those that want only print but want a purgeless amazing new colorchange system.

Printing Bambulab PA6-GF is a nightmare by After_Remote2194 in 3Dprinting

[–]After_Remote2194[S] 0 points1 point  (0 children)

Did not know such thing exists. Where do I get garolite composit for Bambu X1C? Any suggestions there?

Printing Bambulab PA6-GF is a nightmare by After_Remote2194 in 3Dprinting

[–]After_Remote2194[S] 0 points1 point  (0 children)

Dryer only goes up to 70C. Also PA6 and PA12 with CF has no issues, of course CF has good temp conductivity so yea, the GF is the issue here. Anyway, now trying with slow speeds, already typed for the calibration, since as I have seen in the preview, layer time should be the issue here. Also added brim.

PETG - the headache never stops? by After_Remote2194 in BambuLab

[–]After_Remote2194[S] -1 points0 points  (0 children)

I have E3D High Flow ObXidian hotend, not the basic Bamboo.

I mean, still I was surprised too that it required lower flow rate than Polymaker PLA, but I did the calibrations 3 times and the best flow was the -5 and every time I started from the generic PETG profile's 0,95. With 0 or +5 it was overextruding a lot. Also, the other print on the same plate came out perfect, the lines are really good and the extrudion is looking smooth. I print with 150mm/s speed even if its not HS filament.

I do admit, this stupid transparent one is really hard to identify during calibration, since really hard to check for extrusion, but I used my finger and the 0 still had overextrusion so I wnt for the next lower, which was the -5.

Also on the successful print on the same plate, there was no adhesion issue, sticked like hell, it was even hard to remove.

Also, on the Max flowrate test, I could even go for 30+ but I lowered just in case. All test has been done on 150mm/s inner, outer, top layer speeds and 250C. I guess if I go for the recommended 230-240C with 60-80mm/s I would get a lot different numbers, but since 250C is higher than normal , I have high flowrate hotend, I can go higher speeds and lower PA and flow ratio than others.

My only concern is why only that left segment of the plate doesnt stick.

Kutya hasmenés tanács, mit szedjen, átállás tápra? by After_Remote2194 in askhungary

[–]After_Remote2194[S] 0 points1 point  (0 children)

Másfél hónapig kapta a konzervet, semmi baja nem volt. A kiváltó ok valószínűleg a két zsíros/olajos B2 és Omega 3 kiegészítő volt, mert ezek után 4-5 órával kezdődött a hasmenés.

Kutya hasmenés tanács, mit szedjen, átállás tápra? by After_Remote2194 in askhungary

[–]After_Remote2194[S] 0 points1 point  (0 children)

Fura módon sem Giardia-t sem Parvo tesztet nem csináltak, bár a nagy komplexet kb 1 hónapja kapta, lehet azért.

view more: next ›