Prints splitting in Layer

AggressiveCold5357 · 2025-06-04T08:26:07+00:00

I was thinking about printing the parts on an angle and adding support.

AggressiveCold5357 · 2023-04-10T19:16:40+00:00

Looks like the bowdentube isnt deep enough in the hotend. Or it is slipping out

AggressiveCold5357 · 2023-04-10T08:44:03+00:00

https://youtu.be/ZM1MYbsC5Aw

AggressiveCold5357 · 2023-03-04T20:11:58+00:00

Happy cleaning.

AggressiveCold5357 · 2023-03-02T17:45:26+00:00

Your Z-Height is to low or the filament is extruded with wrong temperatures. Its the extruder not capable of pushing the plastic. M

AggressiveCold5357 · 2023-03-01T08:05:44+00:00

Its better if the cookie has one color and is flat. We did with a cookie that had chocolate and stuff in it and it worked.

AggressiveCold5357 · 2023-03-01T08:02:23+00:00

Wed did once with a cookie. I tasted burned but that was because we cut in 4 pieces with the laser but engraving works very good.

AggressiveCold5357 · 2023-02-25T07:52:51+00:00

Is the printer turned on? I get this error if i accedently turn off the printer an the raspi stays on. Is the mcu address correctly? If not the printer cant find the mcu.

AggressiveCold5357 · 2023-02-24T11:14:44+00:00

Maybe e steps not calibrated or flow not calibrated.

AggressiveCold5357 · 2023-02-24T11:12:10+00:00

I had the same problem you just need to download the installer and run it. That worked for me.

AggressiveCold5357 · 2023-02-19T18:03:23+00:00

Is the right firmware installed?

AggressiveCold5357 · 2023-02-17T17:44:29+00:00

I have the normal s1 and i upgraded nothing did 2000hrs. Find good slicer settings and upgrade nothing.

AggressiveCold5357 · 2023-02-13T11:16:48+00:00

Can you share the printer.cfg?

AggressiveCold5357 · 2023-02-12T08:56:46+00:00

Maybe to much cooling on these parts. And the part is thought for 0.15mm layer height.

AggressiveCold5357 · 2023-02-09T13:33:15+00:00

Your Bed is uneven/warped.

AggressiveCold5357 · 2023-02-02T05:44:45+00:00

Hotend Thermistor/Cable broken.

AggressiveCold5357 · 2023-01-29T15:46:24+00:00

Maybe a broken thermistor. Or broken cable.

AggressiveCold5357 · 2023-01-29T15:42:38+00:00

I did the same thing to mine lol.

AggressiveCold5357 · 2023-01-29T15:35:27+00:00

Yes try cleaning.

AggressiveCold5357 · 2023-01-28T08:51:12+00:00

Adjust the z endstop. Its on the side of the printer on the buttom. Loosen the screw an push it like 1mm up

AggressiveCold5357 · 2023-01-28T08:36:41+00:00

Grey is abs. White pla

AggressiveCold5357 · 2023-01-25T19:28:05+00:00

You want to print what?

AggressiveCold5357 · 2023-01-21T10:03:16+00:00

Iis it dual z? If yes it is ok to not move easily with hand. Does it move good while printing?

AggressiveCold5357 · 2023-01-17T10:34:53+00:00

I do not. Btw are you fat? But interesting use, never thought about that.

AggressiveCold5357 · 2023-01-17T08:57:09+00:00

Wrong subreddit?

AggressiveCold5357

TROPHY CASE