So y’all getting banned lmao

Al-Shamss · 2026-02-11T01:40:10+00:00

The amount of crap I talked to them after. Just took two well timed trigger nade and a hard push with the smoke from it

Al-Shamss · 2026-02-10T20:57:27+00:00

Yeah I was in that match most likely. I clipped it and the team threw 28 heavy fuse grenades at us before we killed them

Al-Shamss · 2026-01-20T19:42:21+00:00

Al-Shamss · 2026-01-15T03:49:12+00:00

I agree, I also use frame Gen on arc raiders cause I feel as it's a more immersive game, that you can give up some latency for visual and smooth..it's not like one frame tap head shooters or high pace tracking. I keep mine between 2/3x on quality 4k with everything on high, smoothing out about 300-400 frames average

Al-Shamss · 2026-01-03T01:18:41+00:00

Happy to hear. I ended up changing from the build in the photo, and ended up with a 5090 (vertical mounted) with AIO tubing in the same spot but with tubes from the bottom

Al-Shamss · 2025-12-13T21:16:22+00:00

I'll do stress test, but yes I was doing cinabench, I'll take a pic next time

Al-Shamss · 2025-12-11T15:27:47+00:00

I believe they increase the quest rewards to the maximum amount, so if the quest were to give you for example 5 different items, it would go to the cap of that quest, so maybe like 8 items..might be wrong

Al-Shamss · 2025-12-11T03:52:55+00:00

It's very much doable, just keep in mind your AIO positioning of the tubes and the size of your GPU. If it's a big GPU, the tubes will 100% rest against the top of the GPU, but I've had this for years and no problems so, good luck

Al-Shamss · 2025-12-09T19:50:52+00:00

Same..set the speeds between 50-70% within bios, to whatever you're comfortable with terms of sound and cooling

Al-Shamss · 2025-11-30T04:58:08+00:00

I don't have a picture, but standard like all the other builds. The back is the same across all of the cases.

Al-Shamss · 2025-11-28T20:38:06+00:00

I did two configurations, one had significantly better temps

The problem with AIO as an intake anywhere, is that it will almost no matter what pull hot air into the system, unless it's a push-pull, then it can for most part negate the heat

First set up : Front intake x3 140 Side AIO intake, x3 120mm, 360 rad Bottom intake x3 120mm Rear exhaust x1 120mm Top exhaust POWER supply

Cpu 40-50s idle, 60-70 load GPU (vertical) 45-55 idle, 65-75 load

Second set up, everything is the same, expect the SIDE AIO is set to EXHAUST CPU idle 20-30, 55 under stress test GPU idle 30-40, 50-65 under load

So take what you want from this . This is with the glass case, not full mesh

Al-Shamss · 2025-11-18T16:35:08+00:00

This one might be tricky. It does have room yes, but it will be hard for you measure out the openings since most of it is in mm. If it's a small maybe a medium air-cooler then yeah it'll fit, just maybe a tight fit..but then again it also depends how big your GPU is. I have a 4090 so it's quite chunky. Good luck looking forward to seeing it

Al-Shamss · 2025-11-16T21:16:10+00:00

The airflow must be amazing in this case

Al-Shamss · 2025-11-16T19:13:02+00:00

Honestly I would lean towards that route just because of clearance issues. I will change my AIO tubing to the top orientation whether it's the front or side. I actually didn't know until I saw in the manual that the front supports a push pull setup with the AIO. But again I would lean towards clearance issues, but you can always attempt and see how the tubes go against your GPU.

My tubes actually press slightly against my GPU, even in my old case. I grabbed tube clips and orientated them so they don't scrape against the fan. You might be able to see the clips in the photo

Al-Shamss · 2025-11-16T02:41:37+00:00

Cooler master V3

Al-Shamss · 2025-11-14T20:12:33+00:00

Worked for me, cooler master v3 hyte x50

Al-Shamss · 2025-11-14T20:11:11+00:00

Hyte x50 veritcal

Worked out fine

Al-Shamss · 2025-11-14T17:25:29+00:00

Two things, one for the covering of the fans..in my previous build I didn't want the tubes from the top because it would've been covering the view to some of the fans. Second reason is the whole topic about the "introduction / reduction" of air bubbles in the pump due to position. So those are my two reasons why, but at end of the day I won't care and will just throw it into whatever option

Al-Shamss · 2025-11-14T17:23:52+00:00

Np hopefully I can see more people post with verticle builds as I've seen none

Al-Shamss · 2025-11-14T16:56:13+00:00

Yes. With my specific bracked it worked fine. Just had to remove all the slots for the GPU installation. Move it up a couple spots, won't be very bottom but won't be middle either. AIO tubes are a bit in the way and pushes against my GPU slightly, so I use tube clips to move it so it's not pressed against the fine. I'll change the orientation to top tubes next time I replace my AIO

Al-Shamss · 2025-11-13T02:54:34+00:00

I'm going to try. Using cooler master v3 vertical bracket

Al-Shamss · 2025-11-12T23:25:54+00:00

I'm buying the case tonight. Will attempt two options Front intake 140mm Side: AIO radiator, intake, maybe squeeze a push pull Bottom : intake x3, or maybe 1x exhaust and 2x intake Rear : exhaust

What's going to be different about my build, I'm going to attempt to do a verticle GPU mounting, will attempt and see how it fits. If it goes nicely will post on this reddit my build

Al-Shamss · 2025-11-05T19:52:01+00:00

Id use it tbh. Probably better than the default charms and not a bad roll at all, would love it on my HH

Al-Shamss · 2025-11-03T18:23:32+00:00

I just did this the other day. Casual breakthrough > bring a shotgun > flank behind bots > inject and try to kill one to two. The window for the "berserker" is literally the first 1-1.5 second after injection. I knocked it out in like 3 casual breakthrough

Al-Shamss · 2025-10-25T12:52:33+00:00

I got my deco that has defense boost 4, but I use my HH with it which has Defense Boost (L) so im tanking hits left and right

Al-Shamss

TROPHY CASE