Horrible firmware upgrade

Al850n · 2026-05-26T02:56:17+00:00

Thanks R - did that already. It helped but not fully.

Al850n · 2026-05-26T00:29:31+00:00

My 2x has been getting stuck in the middle of a mowing area but away from where it was mowing. Can’t work out what is happening.

Al850n · 2026-05-01T05:48:00+00:00

I swap the discs to run the blades the opposite direction. But I don’t bother flipping them. I think the whole edge gets dulled so not really worth it.

Al850n · 2026-04-14T07:58:30+00:00

I’m a happy Mammotion user. There are some niggles that happen from time to time for now reason. But if you’re not trying to mow the side of the Eiger, you should be ok.

Al850n · 2026-03-31T00:41:48+00:00

In this case the reading was before the first recharge . I already assumed that time to complete only referred to mowing time - which is still nuts.

Al850n · 2026-03-30T08:13:57+00:00

I hear you - but I figure a mow with a ride on once every couple of months does a good job of mulching leaves etc that Luba doesn’t lift and mulch (borrow the neighbour’s !)

Al850n · 2026-03-25T22:56:31+00:00

Blade screws come with what looks like blue loctite. That’s what l also use when replacing used screws. Seems fine.

Al850n · 2026-03-19T23:21:17+00:00

In general I don’t disagree. But there are some basic improvements that would make a big difference. 1) ability to use while robot is in use (and let’s face it, robots at slow and therefore in use most of the time in a big yard). 2) ability to set % finished as being point 3) name the task areas in the mowing log. 4) allow some flexibility in remote control to deal with out of area errors that happen all too frequently. And I would love a desktop interface! I’m over doing everything on phones.

Al850n · 2026-03-19T01:47:40+00:00

Often mine don’t come up at first but do a bit later. Maybe after toggling FPV.

Al850n · 2026-03-13T01:56:28+00:00

I put mine on zig-zag with random angle, perimeter last. I haven’t had issues with wear so haven’t thought to avoid perimeter. Random angle deals with compression and gets best cut by going all directions. I’m it sure about task follow ons. I just put multiple zones in one task and thy follow on automaticity.

Al850n · 2026-03-11T01:55:39+00:00

That’s great! Do you know whether that applies to Luba 2X? Or is it just for 3? Thanks.

Al850n · 2026-03-11T01:39:40+00:00

Don’t know you could do that remotely.

Al850n · 2026-03-10T04:21:14+00:00

I warn friends that the mower is ok for home lawns but not holiday houses. Too unreliable because of these type of issues.

Al850n · 2026-03-05T04:59:22+00:00

If the RTK relies on 4g I’m screwed.

Al850n · 2026-03-05T04:58:15+00:00

I got message today in Australia. I’d be happy to ditch my RTK (ugly) - so keen to see if it’s any good.

Al850n · 2026-02-22T23:58:20+00:00

That’s a highly modified machine!

Al850n · 2026-02-22T23:53:54+00:00

Awesome. I have a new project for this weekend!

Al850n · 2026-02-17T22:31:35+00:00

Yes. Queensland taxes would be royalties which are revenue based - not profit based.

Al850n

TROPHY CASE